Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello! We have Cisco 2500 Series controller and 25 AP's. Recently I faced with task of disabling 2.4GHz radio interface only on one specific AP. I found two ways to achive it:1. from controller by running command - (Cisco Controller) config>802.1...
Hello,When the MSE gets updated and there are new signatures, does Cisco Prime automtically polls MSE for new signature and show them in the wIPs profile policy? How does that work?Thanks
Hello,I want to start broadcasting not only at a 2.4 ghz but also to 5.0 ghz. I have several access points from Cisco (The 1130AG), we already broadcast 2 SSIDS however we would like to increase it to atleast 3. With one at 5.0GHZ.Since we have a cap...
Resolved! Guest Wireless with 1602i Access Points
Is there any reason why we'd need to use a controller to provide guest wireless from a 1602? We currently have 1142 and had 1130's before and neither required a controller for guest access. I've setup a few other model Cisco wireless access points ...
Hi allWe are looking at a new wireless controller for one of our sites, we currently use Aruba in one of them, and we use mac address authentication so they dont get prompted, it jsut automatically connects which is great! however I see that the Cisc...
Resolved! Wireless guests unable to pass traffic
Hi Folks,This is a bit of an odd one that got me scratching my head, so hopefully the collective can help!We have a wireless deployment that spans multiple sites, the WLC's are located in Central Data Centres and we provide two SSIDs, one for our cor...
Hi everyone,my customer has an AIR-WLC4402-12-K9 using 12 access point with it, and they would like to increase the number of APs in use. Is there an upgrade option for 25? I couldn't find anything, but I suppose the hardware is the same, it's the so...
Hi all,I wan to use cisco 600 AP without wireless controller, just as a simple router or relay to get dhcp from dhcp server. I need help for how to configure it?
Hi All,We are expereincing some strange problems.1. One particular SSID's is appearing very low single strength & rest 2 SSID's are having good single strength from out of 3 SSID's advertised in one LAP.2. Another issue is one of the particular SSID ...
I am testing out using anyconnect network manager to manage our wireless network connections. I have anyconnect installed on my laptop and I have also downloaded the standalone profile editor. I have went through the editor and setup the networks t...
Hello.I have problem with login to AP in Cisco 881GW.I have in running-config default config with memory on flash this router: dir flash: cpc-8xxx.cfg.I write in EXEC mode: service-module wlan-ap0 sessionthen i must put login and password to AP.I wri...
Hi Guys,We're in the process of upgrading our old WLC Controller to a new vWLC Controller and I'm wondering if there is a way to transfer the existing WLC Cert to the vWLC and have both working at the same time? I need them to both work with the sam...
Resolved! MSE 7.5
Hello,Does anyone know how to upgrade license from MSE 7.3 to MSE 7.5 or we need to buy new ones?Thank you.
Current deployment consists of 16 WISM1s running 7.0.240.0 with ~ 1600 APs (predominately 1242s with some 1131 and even 1231s mixed in). Healthcare environment running multiple clinical applications (fusion pumps, IVs, etc), as well as VoFi, Vocera, ...
Resolved! WLC 4404 brick, what can i do?
Hello!Yesterday's power off. After turning on the controller wlc 4404 does not boot.On the console, we get the following:Net: PHY DEVICE : Found Intel LXT971A PHY at 0x01FEC ETHERNETIDE: Bus 0: OK Device 0: not available Device 1: not availableB...
