Wireless

I have one WLC 5508, i set Interface management on port 1 and we have 3 port remaining on controller to use. I try to connect from Management interface to switch but it is not have any connection to switch. I only connect from AP to Interface. i woul...

Hi AllWe have WLC2504 (  Upgraded to Firmware 7.4) and AP'S are AP 1602When Wirless Controller trying to Connects AP'S then they are hanging and same is happening for AP'S os we are not able to do configuration.Pinging continous is breaking for WLC I...

I am deploying a SPA3102 that is forwarding PSTN calls from an analog  PBX to the IP address of a WiFi Handset. There is no server and no  registration in this configuration, just IP dialing.Can you give me  directions.

Hi I have WLC 2504 version 7.4.100 and I need to set up AP policies with MAC and SSCHow can set UP SSC certificateI enabled SSCBut in the controller I see this message : SSC device certificate not present(Cisco Controller) >show certificate sscSSC Ha...

Hi all, I am facining an issue with 7925 ip phones. My enviroment has a WLC 5508 , Lightweight 1041 and 1602 access points. The problem is that the ip phones occasionally flap wireless is connection.The signal comes and goes rapidly and it may take 1...

Hi,I am trying to configure the Access Point module on my Cisco Router (897AVW), however I am unable to route / ping between the router and the AP.In a few examples I've seen, the wlan-GigabitEthernet interface has the command:switchport trunk allowe...

Hi i have a cisco 3850 at a branch site and would like to know if i could use its WLC to join to our mobility group at our Main site instead of having it as a standalone WLC Thanks

Hi, we use a 5508 (7.3.112.0) and 3502i APs. We are having an issue where multiple clients connecting to a single AP(Like in a training room) are being disconnected or generally having a poor user experience. I have attached a debug of a failed sessi...

Hello,Does anybody know what could prevent a Windows 8/8.1 system to connect to a WLC via EAP-TLS? Windows 7/XP do not have any problems here.The radius server accepts the request, but WIndows 8 still tries to authenticate.Software is updated to 7.6....

I have introduced ISE into my environment and need to send DHCP traffic to it for profiling. I have two DHCP servers, however. I would like three fields for DHCP servers in a WLAN. Is it possible to add a third with the current configuration? I'm run...

Hi....My 7921 cisco phone are disconnecting when going from one access point to another access point...what can be reason for this. Should I create a sepearte vlan for voice and data.

I have an a WLC 4402 version 7.0.230.0 with AP's (1130's) running in local mode with a bunch of remote sites. All wireless traffic is sent through the controller at another remote site. I have MPLS with VPN failover. When it goes to VPN it works fine...

HelloI believe since I upgraded my WiSM to 7.0.250.0 is it learning a MAC address on the wrong virtual interface.The setup:- a Linux server with 2 virtual interfaces, both use the same MAC address, one is the gateway of VLAN 116 and one is the gatewa...

I have a WLC 2106. It is currently working as expected over AP's that are connected via a remote PoE switch. I wish to attach an AP to one of the local PoE ports.On a different site we have an identical WLAN controller that was setup before my time, ...

Hello all, Other than not being able to get 802.11ac speeds are there any issues in plugging an autonomous 3702i into a FastEthernet port and not a GigEthernet port?  A new switch is coming soon but the AP will be there first.   Thanks in advance!  A...