Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Bridging AIR-AP1131AG with TP-Link
Hi Guys,Today I want to build a wireless bridge using AIR-AP1131AG (running WLC) and TP-LINK wireless router.The result is failed. May I know AIR-AP1131AG is support bridging the wireless connection with other vendor's access point or not?In the TP-L...
We have a site that would like to have controlled wireless guest access.Approximately 15 access points would be required at site and they have an ADSL2 broadband connection thatalso requires a router.I have looked at the 800 series ISR with adsl port...
We have a customer is a hospitilized environment.Since two months they work full time with the new Dutch Electronic Patient Dossier.We installed 3 Cisco 5508 controllers, version 7.0.230.0 last year on a HP-switched network on a layer 2 mobility doma...
Is it possible to link up a lwapp to TPlink router through bridge mode or repeater mode, i think bridge mode is more reasonable.As some experience guys suggest it would be working if one ap set as Access mode and the remote one set as workgroup mode ...
Resolved! Deployment WLAN with Flexconnect AP's
Hello Guys thanks for reading me again... I hope every one be ok, and I hope you can help me with this problem.I Want to deploy a WLAN with 2 sites one the Central and the other one the Remote. In my central site I have this equipment:2 WLC 55081 Swi...
Dears,Im having a problem using AIR-ANT24120 (12dbi) and Cisco 1242AG indoor , when ever im close to the AP and try connecting with laptop it shows a very poor signal and when im just a few steps away there will be no signal detected at all.Now i've...
Hi all.I`m configuring new 2504. I updated it to 7.4.100.60 and enabled LAG.I want to configure interfaces "ap-mgmt" - for AP management.(Cisco Controller) >config interface create ap-mgmt 69(Cisco Controller) >config interface address dynamic-interf...
Hello, help me pls, how can be disabled "stop-on-failure" feature on Cisco AP2600.Thank you in advance
I recently purchased the following license: L-PI12-LF-100 to add 100 additional AP licenses to our current appliance. When I tried to apply the new license, I received the following error:"Unable to add any license without an BASE license"This system...
Hi ThereWe are working on a solution for deploying OEAP 600 using DMZ WLC 2504. We have a production WLC 5508. The WLC5508 is anchor to WLC2504 for mobile devices. The DMZ WLC 2504 is configured for OEAP 600 to connect and it is connected properly an...
Hi allI have the problem with machine authentication, our customer using Wireless Controller 2500 Series and need implement machine authentication on IAS server. So, as my understand is our controller may not change anything with configuration but we...
A customer runs a 5508 WLC for quit a while. several dozens AP's are spread all over Europe an run just fine. All the AP's have a VPN based connection over an MPLS service provider, so we are using 10.x.x.x addresses only.We have upgraded to release ...
Resolved! Problem with Controller 5760-50
hi all,My customer has a Controller 5760-50, and 30 APs. My customer wants to add 100 APs to this controller.I know that: Controller 5760-50 only add maximum 50 APs...How do I resolve this problem? (buy license or buy other controller can manage over...
Hello All, I have a customer with LMS 3.2 (100 devices license) and WCS 7.0 (100 device license) with less than 100 devices total on both products. Do we need to purchase Upgrade : R-PI12-UP-K9 / LMS 2.x/3.x to Cisco Prime Infrastructure 1.2 Major Up...
Resolved! Regarding WiSM2 License
Hi All,I'll be using WiSM2 for wireless deployment, just want to check if anyone know how the license works?for example if I purchased a license that supports 100 AP, does this means that in WiSM2 controller 1 will support 100 APs and controller 2 al...
