Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi We are facing an issue with the communication between wireless clients in same subnet .These users are not able to ping each other in cisco 881 W wireless router.But we can do in this router to disable this P2P blocking.
Hi experts,Can any of you comment in the attached network drawing. Is the suggested new wlc connectivity correct. Regards,
Hello,We purchased a WAP561 Wireless-N Dual Radio Selectable-Band Access Point a while ago. It was working fine until recently. Our initial setup was having 6 ssids.InternetGuestSystemsInternet 5Guest 5Systems 5The SSIDs that were followed with 5 was...
We have a nightly crashing nightly. We have PI 1.4 instances, just upgraded from 1.3, and each is crashing in the middle of the night. I suspect it may have to do with backing up of the server, but only because that's unique to the wee hours when it ...
Hi all,Some of 'n' supported ap`s (3500 & 3600) registered to 5508 wlc, automatically shows down for 5Ghz and only b/g is up. Code of wlc is 7.4.100.60.What could be the reason..?
Hi All,We have created temporary wireless setup for our users in one floor with 13 APs. In which 9 of them 'n' supported AP's and remaining are only b/g.we have conducted proper wireless site survey and we have placed the AP according to that. But t...
WLC code release notes say that 1.4.1 is required version of PI. It is not shown on TAC downloads.
Hello,I have a question about surveying. I have been doing site surveys and all the site surveys that I have done were all passive mode. I use AirMagnet with Proxim card. I know that there is an active mode for doing wireless site survey. My question...
I have a question about the new Cisco AP 1530 series (AIR-CAP1532I or E).On the data-sheet it's written controller-based. But is it also compatible with flex-connect mode?Because I use a 7500-flex WLC.AP data-sheet:http://www.cisco.com/en/US/prod/col...
Accidentaly disabled a wrong MAC address in WCS 7.0.230.0. Please help me to provide the acces again on network.i have tryed several times to REMOVE the client from the list, unfortunately nothing is worked. Salmasabeel
Has anyone ever had any issues with a UHF 2-way radio causing all wireless within a range to drop?i have a customer that has Kenwood 2-way radios in the warehouse TK-8360HUK & TK-3360, and whenever they key up the basestation to start a call, the pc ...
Has anyone here tested the roaming between Meraki MR APs across different L2 domains?I'd like to know...1) if it works now without the MX appliance,2) how it works (GRE tunnel etc)3) what the throughput is with the handoffThanks,Rogeliorogelio @ rnd ...
Hi all,I'm having some issue with upgrading from Prime 1.2.1.012 to 1.3.0.20I can only find upgrade information for version 1.2.1.12 is this the same version as 1.2.1.012?Until step 4/7 all seems to run ok but its skipping some steps in the process? ...
HiAs we are a NHS Hospital I've kept away from using Lobby Ambassador as we use a managed services to look after our guest access needs.Lobby Ambassador would help out for corporate visitors.My question is using Lobby Ambassador for non paying people...
What would be the proper way to mount APs, 3602E, if my requirements be that they are inside the ceiling and unseen by the end user. No type of external antennas must be visible. Existing APs are inside the ceiling (basically an attic space) with the...
