Support Community, I currently have an issue with my AIR-AP3502i gigabit interface. I connect my AIR-AP3502i to my 3560G POE switch and the port will not negotiate to1GB. I have tried auto negotiate and hard coded settings but when I try tho...
i'm going to upgrade a 5508 wlc code from 7.0.116.0to7.1.91.0to add 3600 series access points having it all manageable via WCS ver 7.0.230.0it seems to be possible, as it is explained in the compatibility matrix found onhttp://www.cisco.com/en/US/doc...
Hi Guys,Good Day,I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would...
Hello,ive got a question about the antenna of the aironet 1310. is there any difference between AIR-BR1310G-E-K9 and AIR-BR1310G-E-K9-R in basic configuration?we had a bridge between 2 AIR-BR1310G-E-K9. but the non-root bridge went broken due its age...
i refer to this forum:https://supportforums.cisco.com/docs/DOC-2975 said that the bug for previous IOS, but mine IOS for the wireless AP is 12.4-25d.JA1 -latest release on 15 aug 2011why i still having this error?mine AP include AP1...
my access point 1230 fail to join the controller. The image is C1200-k9w7-mx.123-8.JA2. I tried to reboot it but it does not join to controller. How do I initiate the discovery process again to make this AP to join? Should I convert it back to autono...
Does anyone know if you can rename a Lobby Ambassador account? If not is there a way to transfer the users created by one lobby ambassador to another?Thanks,Dan.
I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly ?Thank y...
I need to upgrade a 1230 to the new Aironet 1250 at a location. I have only 2 external antennas at that location.I understand that you still can run 802.11n with 2 antennas.But I can not find anywhere in WLC 5508 v7.2 that I can disable the middle nu...
Hi Friends,as of now we are getting on SNMP Trap on our HPopenview moitoirng systembelow trap from WLC ciscoLwappAAARadiusReqTimedOut iNbsnAPIfDown 0x00 23 5d 0f 02 70 0 enable enable unknown access point namecan any one know about these trap.ThanksV...
We have installed a WLC with 5 access points. Those APs broadcast 3 VLANs on different Subnets. We are having an issue where one of those subnets is assigning IP addresses to devices over wired and wireless connections. We are able to ping between...
What support is required for wlc/ldap auth using AD? I am running ver 4.2.205.0 on wlc. I have LDAP server configured with simple bind authentication. Does version 4.2.205.0 support authentication. I read a post that stated authentication no...
Hi folks, I have seen a couple of posts in the forums that are associated to this message but most of them discuss APs not joining or something of that nature. My situation is that I get this error "%DTLS-3-BAD_RECORD: Erroneous record received fro...
Hi allI have some problem about dhcp via VMware 7.1. My client connect the wifi and get ip address well, then, i turn on VMware (inside my computer) and set as the bridge mode. I found that my VM cannot get the ip-address from dhcp server and I using...
Dear Experts,In my organization , we have Cisco ASA 5540 that is configured with the remote access VPN profile. The Remote VPN is configured in such a way that the user authentication will be through Microsoft LDAP ( AD server).Currently the VPN clie...
