Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Does anyone here on the forum have any suggestions to make the Map Editor function in Cisco's WCS easier to navigate?? I have been trying to set the "light walls" on the floor plan I uploaded and it keeps coming out a mess. Also, when I am done add...
I have a (old) 1231 that I would like to reuse, but no one remembers the password. Anyone know how to recover a password from this model AP or how to reset the device to factory default? Thanks in advance -Kristin
Hi,Any help will be highly appreciated.Performance of my wireless network is very poor, pings from wireless clients to the management address of the controller and client default gateway flap intermitently. The set up is a WLC4402 connecting to a 356...
Hi all, Hoping you can help and share idea with this. Now I'm configuring Workgroup Bridge on AP type autonomous connect to lightweight AP. On Wireless Lan Controller, I configured like this link http://www.cisco.com/en/US/products/ps6366/products_co...
DearsI am implementing WLC and also Guest users access... so far so good...I have tested QoS Roles for Guest users, configured 128K for each users... so far so good...But when testing I see that UPLOAD rate is unlimited for them...Can I only limit Do...
Hi,Did anyone use the HTTP PROFILING in WLC 7.3 ?I am using it with ISE and it is sending weird user-agent strings for iDevicesexample for an iPAD: User-Agent$%7BPRODUCT_NAME%7D/1 CFNetwork/548.1.4 Darwin/11.0.0That's oneAn iPone:User-AgentFidelity/...
Hello AllHope someone can help with my question of is it possible to setup a Cisco 1200 AP with 802.1x to drop users into the corprate network if they have a certificate or if not to put them on the guest network?Thanks for your helpAndy ...
I can't use Officeextend because i'm using vWLC.vWLC is sitting at DMZ, CAPWAP Data + Control Port allowed in FW.vWLC is configured with NATted public ip address3500 AP at other side of internet is associated to vWLCFlexconnect with Local Switching i...
Hello there.I got an SSID which has following security settings:WPA/TKIPWPA2/AESI'm now wondering how clients react or should react to this setup when they try to connect to this SSID. Would they try WPA2 and if it doesn't work, step down and try WPA...
Resolved! Configuring WLC with another
Hell,I have currently Ciso4404 WLC installed which is in vlan4001 with the 172.16.10.0/24 subnetI have bought Cisco 5508 WLC recently as AP count is increased... Can I install it in same vlan and subnet? If yes what would be the setting for APs to jo...
I would like to find out the purchase history of a cisco wusb100 product. I have the serial number and I wonder if a cisco technician could contact me to help me find the purchase history. I don't have a contract so I can't find out from the cisco sy...
Resolved! configuring mesh APs on a WLC
In the new IOS versions, (7 and above,) 3502 and 3602s can be set to mesh mode. The instructions say let the AP register with the WLC, then set the AP to mesh mode and the AP will reboot in mesh mode. Is there a way to set an AP to...
After installing Certificate on NGS , Guestconnect wireless connection is dead slow. (takes more than 1 minute to load Splash page ,which is stalled on NGS)We have another Anchore controller with NGS in DR site. Whenever we pointing WLC to DR Anchor ...
HIi have cisco wlc 2504 connected with cisco 3600 ap,now the customer required n bandwidth speed ,but in wlc am not able to enable n bandwidth for ssid.in radio policy of ssid also n bandwitdh is not showing,only this bandwidth showing a/g,g,b/g, and...
Resolved! ACS change Password
i have acs v5.3 and i need change current to new passwordcan you guide me
