Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Guest Anchor Controller
Cisco documentation recommends using a dedicated controller for the guest anchor controller function becuase it needs to be located in the DMZ. However, if I have spare capacity on an existing controller (ie one used to manage APs) then perhaps I can...
Does anyone know if dACLs on a WLC controller using the latest code require a pre-configuration of the ACLs on the controller? All documentation seems to indicate the ACLs must be created first on the controller and the policy engine (ISE or ACS) pus...
Hello Group,I have a 3602i access point and have been looking to see if it was possible to load a Mesh AP image on the AP?
I own a small computer repair company and sold a lot of dell d610 Laptops with a wlan card "air mp-20b" installed. Subsequently three of my customers had hard drive issues and they had to be replaced. To no avail Dell had no driver...
Hi,Anyone seen this before ??-or] Client requested no retries for mobile 00:24:D7:57:48:48*aaaQueueReader: Aug 23 12:40:10.352: 00:24:d7:57:48:48 Returning AAA Error 'Out of Memory' (-2) for mobile 00:24:d7:57:48:48*aaaQueueReader: Aug 23 12:40:10.35...
Hi,I have deployed 2 x Cisco 1522 mesh access point and configured both as root ap. On top of that, I have also customized the power setting for the 802.11a/n signal to value 5. However, I discovered that whenever the mesh APs reboot, the power o...
I have found that there are only few configuration to the Cisco Aironet 600 OEAP.The settings are just for basic configuration for a wireless network when it is in autonomous mode.A need for a Wireless LAN Controller to perform advance settings.Also,...
Resolved! Wireless Mesh & OSPF
We have recently put up a mesh network to link some sites a few blocks away to a campus network. There are two root APs on the campus network and 3 mesh APs, each linking remotes sites. The mesh is its own subnet, each AP is connected to a L3 switc...
Resolved! Is it possible to 802.1x MAB via WLC?
I'm looking for a way to enforce some degree of .1x machine authentication against AD for wireless devices which do not have a robust supplicant and/or cannot join AD. We're using MAC Authentication Bypass (MAB) on the wired side, and a similar capa...
Did any one setup an across WAN WLC as a secondary/failover one for wireless AP? Comapny has one WLC 5508 for each branch office. Management want to cost saving centralize wireless backup solution in a data center. That means if the local WLC fail...
Is there a way to schedule WLAN key changes using NCS Prime? How? I need to change the key to a WLAN on 3 different controllers weekly at a specified time. Shouldn't I be able to do something like this in NCS Prime?
Resolved! WLC 5508 preloaded software by default
While ordering cisco part AIR-CT5508-100-K9 via multiline configurator. My question would be which software version comes whith it by default when choosing SWC5500K9-70.Is it particularly file named AIR-CT5500-K9-7-0-230-0.aes loaded onto controller?...
Resolved! default multicast behaviour
Hi everyone,How does the WLC handle multicast traffic (HSRP,STP etc) originated in the WLAN subnets?Do we need to specify ACLs on filter them or are they blocked by default?If ACLs required, is it best to apply on SVIs or on the WLC itself ?pleas...
Resolved! WLC 2504 and 1130AG
I have a 1130AG that has never been used. I cannot get it to see the WLC 2504 controller. It does pull a DHCP address. With the help of others here, I got the 3502I APs working.Has anyone seen this issue before.
I have a few aironet 1252ag's and they all seem to be having the same problem when making vlan sub-if's. Once you try to set the dot1q encapsulation the ap immediately crashes and returns this dump.12:20:11 -0800 Fri Mar 1 2002: Unexpected exception...
