Hi,I would need assitance on explaining the heat map in Cisco Prime. Some AP's signal are shown as red (-35-45 dbm) , but some AP's are shown as yellow (-55-65 dbm).Utilization, power, comparing the AP which has excellent red signal and yellow/green...
Hi all,I've seen this problem more than once..Today I Installed AP-adder Licences and so hat to reload the controller (7.4.100).because of the AP-SSO Cluster, I hat to wait a few minutes and than could failback to the Primary controller.All seemed to...
Where are the AP groups in PI 1.3 ?The documentation in PI 1.3 states Step 1 Choose Configure > Controller Template Launch Pad. Step 2 Click AP Groups or choose WLAN > AP Groups from the left sidebar menu.AP groups in the controller itself shows the ...
Dear All,I am trying for the migration from WCS to NCS. I need some help for the below steps been taken by me is correct or not...1) From WCS - Export XML file2) From CISCO Portal (Licensing)- Get newly generated license3) Install NCS 4) Add the new ...
Hi,I have a WLC5508 with around 70 AP's (LAP1042N) connecting over an MPLS WAN network.WLC and AP's are running 7.4.100From time to time I have an AP which disassociates from the WLC with the logging beneath.Can anybody tell me if this is a problem w...
Hello,We have installed 2 new WiSM-2 in HA with software version 7.3. We have also upgrade NCS 1.1 to PI 1.2.After adding the primairy WiSM-2 in PI we can manage the WiSM-2 for a short time from PI. But after a few minutes we lost the connection to t...
Hi,I´m wondering if there is a possibility to mark wlan-traffic network upstream (meaning traffic leaving a LWAP towards the WLC) with a dscp value even if the client doesn´t send any WMM information. thanks fpr your help
Hello,We have currently a WLC 5508 using 8 ports bundled into an etherchannel.We would like to remove one physical from this etherchannel and use it for providing an access to Internet only,Is it possible to create an virtual interface on the WLC tha...
Hello Community,I am having a very peculiar issue wherein an 1142 WAP is randomly disassociating and powering down due to what the Trap log is calling a "Watchdog Timer Reset." The only way I can get it back up is to power cycle the AP. Currently the...
Hi, folks,when I try to boot MSE, I got this prompt(repair filesystem) 1 #Is there anyway I can fix it other than RMA ??
Hi all,I have a MSE virtual appliance and i need to configure Location Service and CAS / wIPS.¿Is it necesary to deploy 2 MSE to have those mobility services?I read two notes about this configuration that confuse me.Thks!!!Rolando
If I have a PI 1.2 system that has multiple interfaces configured I can upgrade to PI 1.3 and both interfaces remain and I can see both under the admin webpage under appliance interfaces. But if I do a fresh install of PI 1.3 I can only configure on...
Hi all,I'm looking for getting a Cisco prime NCS appliance (PRIME-NCS-APL-K9). I'm a little bit confused regarding to the license scheme:1. Does the appliance has any license coming with it or we need to order the license separately?2. If I have an W...
Users complain that wireless device would lost wireless network connection when they moved from one AP coverage to another AP coverage. They have to reconnect to the wireless network again.In our wireless environment, all APs are connecting to a sin...
All,I keep getting the following alert in Cisco NCS anyone have any insight?CPU Receive Multicast Queue is full on ControllerThank you in advance.izzy
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |
