Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hello,I need to replace a 4402 with a 2504 controller and put a 2504 controller in the DMZ for guest access. This would be the setup:The 4402 would be replaced at a remote site (not hreap) and support a couple of wlans, one of those would not be loc...
Hye,I have 40 clients connected to the aeronet ap , all was working fine, then out of the blue two laptops stopped seeing the ssid, it disappeared, now bear in mind the other 38 laptops are working fine, and connect normally to the ap.I went to the e...
I am curious if I can do an either or sitution with a single SSID.If you are on the mac filtering list then you gain access to the network, if not then enter your WPA2-ENT credentials.I have a minimal ammount of users that need mac filtering, but do ...
Hi, I'm looking to implement guest WiFi access with web authentication on one of our 5508 WLC (currently deployed within a sandbox environment), but looking for some assistance. The WLC currently has a single connection from port 1 to the 'Test Site ...
All,I need help and advise on my current problem. Basically at home i am using normal sky router and signals are really bad in garage and room upstairs. I can't run through a cable. Is there any thing which i can use wireless. Please advise. ...
Hi,We are trying to setup a a segregated DMZ wireless network.I've attached a simple topology to illustrate. So we have foreign controller and anchor controller. Firewall ports UDP16666,16667 and IP97 have been enabled and EoIP tunnel itself is up.Th...
HelloWe got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. appreciate to ge t cisco document to follow the steps if the above is doab...
I have build a RAP / MAP setup on my WLC with a switch behind the MAP. Every thing worked here on the desk. Even disconnected it all and reconnected it before shipping it off. The APs are 1242AG on a 2504 with 7.0.220.0 softwareThe only difference is...
I am trying to setup a 4400 WLC with 2 different AP Groups mapped to its respective Dynamic Interfaces / Vlans. AP's are equally mapped to both the AP groups by Floor wise ex: First floor AP's connect to one AP group and the Second Floor AP's connect...
We currently have some LAP1242AG AP's meshed together inside our building.The owner (without consulting IT) was able to aquire some LAP1510AG's that he want's to deploy for outdoor use.Can they be meshed into our current network without having to cab...
Hi,We have 80 LAP1252AG and WLC 4404. We plan to upgrade our WLC 4404 to WLC 5760 but not sure if our current APs will work with the new WLC 5760. Hope you could help me out. Thank you.
HiWhat would be the best option to monitor the load on AP live? Is there a GUI tool for this or should I use command line interface? I was hoping that CNA would do this, but the AIR-SAP1602I.EK9 does not seem to be supported by the CNA. CCP seems to ...
I am configuring an 1142n. I am testing to make sure the 5GHz radio is functioning properly. When I disable the 2.4GHz radio, the SSID stops broadcasting. Is this expected behavior?-Thanks
Hi, We try to setup remote APs in FlexConnect mode and wants it set for local auth, while the main site (where the WLC resides) uses central authentication.The SSID has is the same at both site so is the L2 security policy.thanks,Alex
Before I go purchasing new stuff I need to know if this will work.I have 12 1130ag's in a building being managed by a 2100 wlc.We're thinking of replacing the 1130's with the 2602. Will the 2602's work with a 2100?We also have a 2504 that can have mo...
