Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi All, We just upgraded some of our devices to IOS 5 (IPAD and IPHONE) and wifi stopped working after we turn on/off the devices. In order to make it work we have to erase and recreate the wireless profile. Is anyone experiencing this kind of proble...
All of a sudden I have Lwapps refusing to attempt to join my secondary controller. Both controllers are in a mobility group located in a centralized data center. My primary controller is full and is obviously rejecting the wap's request to join. U...
Tacacs not working for 3 new 5508 WLC's...working fine for 6 old 4400 WLC's.before 7.116 code upgrade...I remember 5508 was working on and off and now they are not.Same configs on SW, WLC and ACS. Debug on WLC gives..below message when Tacacs is atte...
We recently had a user go to a congerence at another location, and when they connected to the Wireless there, they were automatically redirected to the locations Website.I have been looking through the WLC Config guide (7.0), and the only thing I am ...
Hello.I have a project in an industrial environment which requires high speed wireless connectivity between 6 buildings,one central and five remotes.The maximum distance from the central building is 100 meters (take o look at the attachment diagramm...
Hi,I have a 5 Aironets and wanted to setup these up as repeater?The Root is going to be unreachable for 2 of the aironets, it is possible to set these up as reperters to repeat from the closest repeater, or can I set up the repearter to repeart from ...
Resolved! 5508 Controller & Muliticast
have a Cisco 5508 controller (version 6.0.199.4) that when I enable global multicast mode it will work for an hour or two and then it will kill the network. All internet both wired and wireless, access to server everything dead. I then have to dire...
HiI wonder if someone could help me with the following querry.We have deployed a Cisco Unified wireless network for accessing the LAN (we use manyy VLANs). This uses a Cisco 5500 series wireless controller and several LWAP connected to different Cisc...
Resolved! WLC 5508 Guest Controller licensing
Hi All,I have purchased the following hardware with the following configuration:WCS-PLUS-100 Cisco WCS with PLUS License2 x AIR-CT5508-100-K9 Cisco 5508 Series Wireless ControllerOne controller is in use for Corporate, the other is the Guest Access c...
In my WCS v7.0.172.0, I recently configured the Controller Configuration Backup task. Backups seem to be working fine for the past few days. How do I tell it how far back I want to keep logs, or how many log files to keep before deleting the older on...
Hi all,First, sorry since this is not related to any configuration discussion.I would like to know if it is feasible to put those Aironet AP with internet antenna like AP1142 / AP1042 in a enclosure box (Like IP66 grade) box. Will those enclosure box...
I have 7 WLANs configured all work fine but the latest. The 7th WLAN I configured will not let clients get an IP address. I can plug a wire into the port with the same VLAN configured on the port and I get an IP address but wireless clients connected...
So i am not sure about data rate speed of AP1041 single band. It able to support 300 mbps or not.Refer to datasheet i saw PHY data rate 300 mbps just only dual band ?Thanks for advice.
Weird issue:I have some handhelds using certificates to connect to the internet in my office.The handhelds can connect in all the complex but inside a warehouse, all the config for the APs is the same, we use 1242s and 1131s (yes inside the warehouse...
I have a client that wishes to use EAP-TLS for machine certificate authentication, but they wish to authenticate users using their username and password not a certificate. Is this possible? The main objective is to ensure a stolen or unattended lapto...
