Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
It seems that in order to execute RESTCONF queries against the WLC, a user with admin access (privilege level 15) is required. Is this true? In order to execute read-only get queries against the WLC, you need an admin user?
I am trying to understand why an AIR-CAP2702I-A-K9 remains functional when the VPN tunnel to the WLC is lost but an AIR-CAP3802I-B-K9 does not. They are both connected using Flexconnect to the same CT5508 wireless controller. Both models of APs are i...
Resolved! compatibilty matrex for 9800 wlc
actually we are planning to get new 9800-L , is bellow access points supported by 9800-L Wireless controller , and if it is supported is there any feature and version limitationAIR-CAP3602I-E-K9AIR-CAP3702I-E-K9AIR-CAP3602E-E-K9AIR-CAP2602I-E-K9AIR...
WLC-9800-40Sw: 17.9.3Hello, I have a client issue with a user. He dissconnects very often and a radio trace and clientinfo shows this:Any suggestions what to check ?regardsJohann Folkestad
Hi,I was investigating wifi issue forthe users , they cant get dhcp and noticed some discrepancy in the config , I am not sure if this can cause. Can you help with expert review? So, Wireless/AP/General/IP config dhcp shows 10.2.0.1, mac address of t...
I have a 3504 HA pair of controllers which have 100 registered APs on them currently and they are licensed for 150 APs. They are a mix of 2800/3800 and a few 9120s. Recently we purchased a few more 9120s. They are all being added to the same Vlan...
I'm trying to get the details for the Cisco C-ANT9103 on Cisco Prime/WCL. Is there an option on Prime to get the details (serial number) of the antenna connected to the Cisco C9130AXE-E Access point, As it is in production and running, I have only th...
So i have the following problem, i changed the access point from lightweight to standalone and configured it with a static ip which i can ping. When i try to access the web gui i get the response "err_connection_refused" from my browser. I tried seve...
Resolved! Internal DHCP on C9800 for Wired Client?
Hi, If create Internal DHCP on C9800 for Wireless, It also distributes IP DHCP to wired clients in same vlan. Can it be disabled IP DHCP to distributed to wired clients? Thank you so much.
Hi all,I have some questions about LWA, I configured everything and I get login page and can login and everything works fine. The problem is that I don't want to use 192.0.2.1 address for guest portal, when I set Virtual IPv4 Address to guest-wifi.co...
Resolved! AP cannot join to Wireless Controller
Hello everyone,I am trying to make my AP C2600 to join to my exiting Virtual Wireless controller which has already controlling over 10 units. They are c2700 series.The AP C2600 was used and connected to other Wireless controller before but it was dec...
Resolved! IW9167EH-B Failed to Join 9800 WLC
Hello!Im upgrading some of my Cisco AP's to IW9167-EHB's and the AP is stuck in a loop.I'm getting the following errors:[*08/11/2023 00:34:09.8578] CAPWAP State: Discovery[*08/11/2023 00:34:09.8588] Got WLC address x.x.x.x from DHCP.[*08/11/2023 00:3...
Hey Guys, i just want to have a quick check what is the best way to upgrade the 3.8 CPI (running on VM) to 3.10.x After some good reads from cisco docs, i understand that only way to upgrade is to create a new VM, install 3.10 and restore the backup ...
Resolved! C9120AXI AP POE Power
Hello Team, We have connected C9120AXI access points to WS-C2960X-24PS-L switch. It is consuming 30 Watts of power. Is there any way to reduce the function of AP so that it can consume power less than 30 Watts? Below is the output for Show Power Inli...
Resolved! C9800 with ldap
Hi, I am trying to access SSID through AD authentication with C9800 WLC, Active Directory, C9115. Each equipment versionC9800: 17.3.3 (vWLC)AD: This is an AD created on a Windows server, and there is no problem with AD itself because it is currently ...
