Hello all,we are using 5520 wlc(8.10.190.0)and ap's in flex connect mode.currently we have migrated to capptive portal for the guest authentication.users are getting authenticated but they are not getting the ip address, in cisco ise the user is auth...
Forum Posts
I have a WLC9800 L. I installed a wildcard cert and set a trust point. Now I cannot access the management via GUI. I can still access via putty using the IP. I followed the Cisco documentation for installing the cert but Haven't found anything on t...
Dear Gents, What are the recommendations that should be followed if we have a local site with wireless APs operating in Local Mode and registering on a local Primary WLC on the same network. and in the case of Primary WLC failure, the APs w...
I need to change the hostname of a 9800-80 HA pair with thousands of APs and clients connected. Thinking about the primary and secondary wlc names configured on APs for the capwap join process, how do I gracefully change the WLC hostname? The ip ad...
Hi there, I am upgrading a bunch of WLCs at different sites from 17.9.4a to 17.9.5.I am performing the upgrade using GUI (browser) with ISSU Upgrade tickbox ticked (AP upgrade per iteration set to 5% to minimise disruption).Problem is, 2 of the sites...
document related to machine authentications using ISE in meraki wifi infra for the corporate devices. I got to configure using user authentications. searched many forums for the same. can anyone point it to correct documentations or link to configure...
Hello All,I cannot get C9130AXI-B Access Point to get IP addresses from DHCP Server.ConfigurationDHCP Server (dhcpserver.de) is on Win 11, connected to Cisco Catalyst C1200-8FP-2G PoE switchC9130AXI-B running EWC image v17.12.03 connected to the same...
I recently configured 802.11k and 802.11r in order to get the company iPhones to roam seamlessly between APs.Now I'm getting following message every once in a while in all AP logs I checked:May 13 05:17:33 kernel: [*05/13/2024 05:17:33.2509] RSNIE in...
Resolved! adding new ap into existing EWC
I am trying to figure out how to add an ap into a an existing EWC network currently have one ap c9130ax and I am trying to add another c9130ax both same country code, the new Ap has been reset and I believe it is in Capwap mode, currently I am unbale...
Environment :- 9800-80 SSO.Issue logs :-install_add: START Mon May 13 10:57:58 2024install_add: Adding PACKAGEinstall_add: Checking whether new add is allowed ....--- Starting initial file syncing ---[1]: Copying bootflash:C9800-80-universalk9_wlc.17...
As of now, we are using WLC and Access Points as per the following make and model:Cisco Aironet 1815i Access PointModel: AIR-AP1815I-D-K9Software Version: 8.10.185.0Now, we have purchased new Catalyst 9100 Access Points:AP Model number: C9105AXI-DAft...
Greetings, Kindly advise how to check and rectify cisco outdoor AP1542I for not powering up. The WAPs are connected to 9200 series POE switch and the switch ports are able to power other devices when connected. End user found that 4 out of 18 instal...
Hello everyone,I'm trying to figure out a frustrating issue. Attempting an install of APSP6 keeps bombing out and I'm unsure what steps to take next. Software: Version 17.09.04aROM: 17.3(3r)Error in question: Dec 13 21:21:01 Eastern: %INSTALL-3-OPER...
I have a Cisco 3700 Series AP and trying to connect it to a WLC 5508. I have getting a certificate validation failed error, however when I use the command "show crypto pki certificates" no such expired certificate shows up. Previously had an issue wi...
Hi Guys, I have face a very weird issue. Currently my environment are running with 2 x C3504 in HA. There have 18 AP mixed with 1702, 1852, 2802, 9120. Some support for CleanAir some not. Too use all this model, we had choose the version 8.10.130. S...
