Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
I have 5 WLC's (3-2100, 2-4400) and need to synch the NTP server ip addresses on them. I know how to do this but have a question. Using the gui, once I apply the change to the NTP ip address and save the changes, will the WLCs need to be rebooted f...
Hi!Is it possible to see on older autonymous ap (1121) ifthey are missing MIC certificates ?Br
Hello,I am trying to create a network in which there are four bridges communicating wirelessly in point to point design(Two bridges on each end of the network which are the connected to Catalyst 3650 switches). I have achieved this design but when I ...
We have clients that will randomly disconnect from an AP and then cannot connect again until the AP is rebooted. We have unselected exclusions and they are not going into an excluded clients list. Any ideas?
/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm ...
Hello,I'll need to supervise a WCS (release 4.2.) remotely through SNMP.What mib can I use to get information such as CPU used on the WCS, free space HardDisc, number of AP, number of rogue AP, number of LWAPP tunnels , number of wifi users connect...
Hiwhether the 1142n access point work in 100Mbps PoE port or it will work only in 1000Mbps portThanksKarthik
hello everyone,we have since a few days the WIP310 phone and some problems came with it.#1 the WIFI wizard (ver. 1.0.17)i am telling the wizard to select WPA2 as WIFI encryption. on the next page ask the wizard me to enter a passphrase to generate WE...
Hi!I've got 2 wierd problems using our 1142N APs I can't seam to solve.We are configured to have 3 WLANs. 2 of them are H-REAP, with a VLAN number depending on the building the AP is in. The last one is a Guest VLAN.First : When some APs are rebooted...
My,My wireless network have Cisco WLC4402 & AIR-LAP1142N, and configured with 3 SSIDs. May I disable radio band for individual SSID?for example :SSID1 : enable 802.11a/b/g/nSSID2 : enable 802.11a/n onlySSID3 : enable 802.11b/g/n onlyThanks a lot.Jack...
i am trying convert my AP from ightweight mode to Autonomous mode, i av already followed all the required steps but i am getting the following error messageson AP console: ERROR: Failed to extract from archive file tftp://255.255.255.255/c1240-k9w7-t...
I have a WLC (4402) running version 5.2.193.0. The WLC used to have both interfaces connected to a single switch (LAG was enabled) with etherchannel on the switch end. It was changed such that each port on the WLC is connected to a different switch...
Hi folks,I've run into an annoying issue with 6.0.196 with my favorite (Motorola/Symbol Fusion) client. Ever since some testbed controllers were upgraded, Symbol MC90 handhelds have been unable to roam successfully across controllers. The EAP-TLS c...
Hi allI am new to Cisco and I need to upgrade the Cisco AiroNet 1200 AP's at my place.The current version is 12,2(15) JA I am not sure what is the latest version available, the reason for the upgrade is to allow WEP Encryption which is not an option ...
I have acquired a brand new AIR-AP12THD-A-K9 Aironet 1200 series access point. I believe this unit is similar to the AIR-AP1232AG-A-K9 unit. The unit is running IOS Software C1200-K9W7-M Version 12.3(2)XT1, boot loader C1200-BOOT-M Version 12.3(2)JA...
