Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Is there anyway to assign users to different vlans with ACS/Automous AP's? I know how to do this with CUWN but not with Autonmous. Any ideas?
Hi,having no problems to get the AP's attached and configured via the WLC, but i'm not able to get the DNS-resolution in the LAN done proper.That means: Having 3 AP's connected to WLC2106, this one is getting it's DNS for one SSID/VLAN from an extern...
Hello everyone.I have a client looking at deploying guest access to several sites. The issues are that all the sites arevariable in size so we are trying to get a one size fits all which is difficult.Generally all sites will use controllers or HREAP ...
Hello, I have a WCS with version 4.0.97.0 and two controllers with version 4.0.217.0. and two models APs: AIR-LAP1242AG-E-K9 and AIR_LAP1131AG-E-K9. The problem is that I am unable to configure the templates WCS WLAN Override. I can set the controlle...
Hi,I'd like to know if there is a way to authenticate using a username with PEAP and in addition restrict the access with the station MAC address. Im using 1230 APs with Cisco Secure ACS authenticating with the Ms AD.Thanks in advanced
I upgraded my 1131AG AP from autonomous to lightweight with file "c1130-rcvk9w8-tar.123-11JX1.tar". Now, I can't get the AP to join my WLC, and the lights on the AP constantly blinks red, orange and green. I can't get the AP to get an IP from my DHCP...
Is there any way to prevent users with a virus from accessing our wireless network? Intrusion Protection and NAC are not yet installed. Would I need to temporarily enable MAC filtering on the WLANs and add the MAC of each wireless device I have verif...
How long can a HREAP AP remain in standalone mode without a controller?And how do you extend the timer?
I have a 4402 WLC configured on the management VLAN and 9 AP's that were converted to LWAPP. When the AP's attempt to connect to the WLC, they download the image then display the following error. "No more AP manager IP addresses remain." The AP's the...
hi!I want to run 802.11A for VoIP and 802.11G for data WLAN. 1. do I need a pair of antennas for 2.4g and another pair for 5g HZ? four of them?2. does AP support dual-bands at the same time?
After upgrading my WCS to 5.0.56.0 and 4402 wireless controller to 5.0.148.0 I have noticed that the Guest user accounts can only have a maximum validity period of 30 days. If I add more than this in the WCS or choose unlimited I receive errors. In l...
My setup: 2106 controller with 4.2.205 firmware, 4x: ap1030 radio. We presently add 2x: Air-rm1252g-a-k9. My problem: I'm not able to activated the 40 mhz bonding channel on the Ap1252. I always receive the message: "Slot is not enabled or customised...
I have 50% CPU load with all interfaces shutdown and I see the are two processes (dot11 driver and HQF).I just learned HQF is QoS related:QoS is disabled by default; however, the radio interface always honors tagged 802.1P packets even when you have ...
i am looking for an antenna that is stronger then 5dbi for the 1250 n, however i am unable to locate it on any data sheets. I am in need of an omnidirectional <8 Dbi gain antenna, does such a product exist? Thanks for your support.
I need advise on setting up a bridge between 2 buildings ¼ mile away from each other. There is clear line of site. I need to be able to provide wireless on the remote end only. I was think maybe a 1400 series with a Omnidirectional Antenna at the HO...
