Cisco Licensing really screwed up with their AP licensing for these “shared” APs. Attempting to run these APs using a 9800 on prem controller has proved to be problematic for licensing. So far I have spent 20+ hours on calls with various TAC engineer...
Forum Posts
had preformed a firmware reload (boardinit bundle-axel-SS-8_10_130_0.img) on the ap and got through the setup process with out issue. AP was pingable and web interface was functional. However when I power cycled the unit, it was no longer pingable...
Resolved! WMI and AP Management IP range
I have an existing infrastructure where the AP management subnet (192.168.4.0/22) is the same as the WMI (192.168.4.2) on a 9800-40-K9. So the radius source address on WLC towards ISE is 192.168.4.2. Currently i have an existing infra with 10 APs but...
Hi We have AP 2702 and 2802 running with WLC in version 17.9.5 As per compatibility matrix of below link , there are some software versions not supporting 2700 as 17.12 and 17.13 https://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/com...
C9124AXE-B running EWC 17.15.5.36 is reachable on management IP 192.168.x.x, but the GUI is inaccessible. Conversion from CAPWAP back to EWC completed successfullyInitially, HTTPS was bound to CISCO_IDEVID_SUDI. In that state, TLS to 192.168.x.x:443 ...
When is check CW9164-AP-09 showing Ethernet uplink speed degraded. So how can the CW9164-AP-09 connect to cloud speed rather than disturbing by switch port that can only do 1GB but with cloud it can be converted to 10GB. my Question is how this can b...
Hi Team,We have deployed approximately 350 EliteBook 830 G9 devices in our office environment, all equipped with Wi-Fi 6E capability (WLAN Card: Intel AX211). To support 6 GHz connectivity, we have also deployed Cisco AP-CW9166I-ROW access points acr...
Hi everyone,I am working on a university network project using Cisco Packet Tracer 8.2.2 and I am stuck on a WLC wireless issue.Setup:Layer 2 wireless switch connecting WLC, LWAP, and RADIUS serverWLC management IP: 172.16.99.21/27, gateway 172.16.99...
Hi All,We have a deployment consisting of multiple Cisco IW916x Access Points managed by a Cisco Catalyst 9800 WLC running IOS‑XE 17.18.3. The setup is as follows:One Coordinator AP (IW9167E) connected to the access switch on the shop floorOne Base ...
Resolved! Issues with Sponsored Login - MacOS
Hello Everyone! Running into a slight issue with the Sponsored Login configuration. I currently have an SSID with Sponsored Login enabled. All devices excluding anything running MacOS is having issues connecting to the captive portal. When trying to ...
Model: C9800-40-K9 Hi Wireless experts,C9800-40-K9, SSID, WirelessI have a problem when creating a new SSID1, suddenly my existing SSID2(related to voice, like phones connect here) will go down like SSID2 still up and broadcasted but phones cannot he...
Hello, I have an Ap (MR46E) that has an alert of "Ethernet uplink speed degraded". I've checked the cable by investigating the port...no errors, CRCs, drops...cable seems good. I've bounced the port. I have the port set for auto/auto and the port is ...
mportant noteMR45/55 APs are not supported on MR 32.x.x and will instead upgrade to the backup version (MR 31.1.8) if they are in networks configured for MR 32.x.x versions, and thus, new features will not be available.EnhancementEnable class 2 PoE (...
Resolved! 2802i U-Boot issue
Have 20+ 2802I with U Boot issue on a 5520WLC, have tried booting from different partition, but still the same.Capture shows this, so not sure if corrupted. But just keeps going round and round.These are not under support, have seen Solved: 2802i AP...
Resolved! Boot error on CISCO 1852
Hi,I have a CISCO 1852 Access Point stuck at (RNAQ-C7) prompt after boot and detecting a nand0 error. Here after the boot log ...Is it a hardware error ? If not how to reload a firmware using maintenance link ?Thanks for your answers.U-Boot 2012.07 (...
