Wireless

Hi!Is it possible to convert AIR-AP1231G-E-K9 and AIR-BR1310G-E-K9-R AP's in LAP mode?thanks for your anwersLasse

I have one vlan interface with two ip addresses, 10.10.10.1 and secondary 10.10.11.1. On Windows server I have two scopes 10.10.10.0 network is for wired clients and 10.10.11.0 is for wireless clients. How I can get wlan AP's to get address from 10.1...

I am current setting up a simple wireless network consist of 2 Aironet 1130 AP,1 WLC 2106 and 1 Catalyst 2950 24 ports.I configured the AP Manager and Management interfaces both on the VLAN 30. at the same time I configured Catalyst 2950 Fa0/6 to be ...

When I back up my configs I am now seeing this message against some devices. I have checked that I only have 580 devices and the limit is 2500 (ish). I have also set up smaller jobs below the 500 collection limit to cover that possibility, still th...

Hi allI am facing a strange problem today. I have a 1242 root and a 1242 nonroot associated to each other via the "a" radio. When I check the association table of the root, I can see that the Root is associated to a different IP address than the Nonr...

Hi, We are trying to implement a BBSM 5.3 into a L3 environment for Guest access for our Wireless users. We have a WLSM module in the core and 1131AG AP's distributed across 5 remote sites.The switch discovery wizard on the BBSM seems to fail since ...

Hi,I've a trouble with config group in WCS 4.0.97 with the following step:- set-up 2 templates ( server authentication )- selected 3 controllers in the same mobility group- applied these 2 templates to the controlles ( all worked fine )- checked with...

Hi all,Can somebody ,please, clarify for me what the command "show dot11 statistics client-traffic" shows to me? The output usually looks like:xxxx.xxxx.xxx pak in 24289 bytes in 5050182 pak out 32230 bytes out 35936358dup 47 decrpyt err 0 mic mismat...

We had a strange problem after installing a 4402 controller and several new 1131 LWAPP ap's.Many of ours clients did not receive ip when trying to connect to the network. Then we discovered an older ios ap powered on. When we powerd this ap off, the ...

Hi Sir,I found the following from Mesh 1500 datasheet for its power requirement, 95?260 VAC, 47?63 HzPower over Ethernet: 48 VDC, +/?10 percentHowever, my contractor requested me to give him in Watt as UPS is provided to it. Can anyone show me the fo...

Can I know the tool by which I can measure the signal strength and the S/N ration and the IP address and the rest of the detail?can anyone help me on these.

Hi,I'm in the pre-sales stage of a new WLAN for a large(ish) hotel (32 AP's). We are proposing a 4402 WLC and AP1010's.It turns out that the customer does not want the added effort of generating one time user credentials for the guests. Is there a wa...

I have an AP that has been upgraded by someone else. The 802.11g interface does not come up, and an error message "*Mar 1 00:03:15.367: %DOT11-2-NO_FIRMWARE: Interface Dot11Radio0, no radio firmware file (flash:/c1200-k9w7-mx.123-8.JEA/5501.img) was...

Does anyone know? I'm mounting patch antennas on an outside wall, drilling a small hole in wall, and connecting the antennas to a 1200AP on the inside wall. I plan on setuping up a fiber segment on the cable run to the switch. My questions, 1) Shoul...