Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I am having an issue with my 4402. In the WLAN I have created there is a setting called Session Timeout. This by default is set to 1800 secs. This forces the clients to reauthenticate on the wireless every 30 minutes. I want to change this to 28000 s...
Hi,what is the highest secuirty that we can provide to the wireless phones which are communication with VOICE SSID.pl help me with configuration for Autonomous AP's.
Resolved! MLPP with LWAPP deployement
Hi,I would like to know if you LWAPP APs can handle MLPP. My feeling is that is not possible since MLPP use RSVP on each node on the path and since QoS in LWAPP mode is propagated via LWAPP tunnels. Am I right? For example I want to deploy Aironet 15...
Hi All,I have been running a WiSM successfully for months now, but our wireless network has grown quite a bit so we have purchased a second WiSM. Are there any best practises for implementing another one, or are there any design guides?Thanks,Michael
I am using Cisco AP1121G access points with Cisco PI21AG cards(and ACU) running WPA2 with LEAP authentication against an ACS server. The problem is that the clients experience a constant slowdown. When a client is started, it will run fine for a coup...
Resolved! the use of RRM ?
we did an site survey for a warehouse in witch we had 20 ap's (1050) foreseen, we made a channel map with power adjustments, once the installation was complete we enabled the RRM feature on the controller, this feature should fine tune the rf enviore...
I understand the Cipher TKIP is the most secure encryption for a point-to-point bridge. I have enabled Cipher TKIP on both sides, but do I need to enter a n encryption key? If I do where do I enter the key at? Also is there a sample basic config for...
I have an out of service AP 1131. I have a replacement ready to install but I'm concerned w/ the map on the WCS. How can I go about replacing the existing AP w/ the new AP while using the existing name?Robert MaldonadoSr. Systems Administrator
Hello,concerning the floor maps of a building: is it possible to show the coverage caused by an AP which is on a floor below or above?Thanks for any advice, p.k.
Hi,The goal of our application is a data transmission network between the ground infrastructure and vehicles. On the ground, we planned to use LWAPP AP1242 managed by a WLC. On board, we planed to use a MAR3200, fitted with 2 WMIC. In a first time, w...
Hi AllI want to soon disable 802.11b support on our AP 1231 with B/G cards. I want this because I don't like to have 802.11b clients connecting and taking down the speed.The question now is, how would our signal coverage change if I put 'power local ...
I am having a problem with the WISM blade blocking UDP traffic on port 6001. This is for a Sentinel Hardware Key. The software sends out a UDP request but it appears that the controller just drops it. I have tried an explicit permit ACL on this ne...
We have a 3com 3c17205 PoE switch, we have replaced the 3com wireless AP's with Cisco 1231's, can we use this switch to power the 1231's?
How long does the client's credential keep in WDS AP? and is there any method to not authentication through WDS AP? I'd like to using only Radio Mangement for WDS without Fast Roaming. Sometimes many client's authentication request make jamming by WD...
Hi,how do we provide security for the communication to happen between root bridge and non-root bridge.do we need have any additional security devices.Situtaion:1 root bridge and 1 non root bridgessid broadcasted and distance is 4 kms communication ne...
