Wireless

Hi,We want to do AP Group VLANs.Described at,http://www.cisco.com/univercd/cc/td/doc/product/wireless/hahcont/wlansc.htm#wp1040568It's quite clear how to do this in WLC Web GUI but I can't find any reference to it in WCS docs.Can WCS create AP Groups...

Hi,we are using 4 WiSM with 8 wlc and software version 3.2.116.21. We deployed about 550 Lightweight AP's Aironet 1131. After a few weeks, the wlc stops logging messages to the syslog-server. Also the webinterface is affected. It restarts logging to...

We are planning to upgrade our wireless network by replacing all our 350 bridges with 1300's. However this wont happen for all our sites and we are thinking of replacing all our root bridges with 1300's and will replace the 350 bridges later. I have ...

I have tried upgrading 350 root to 1310 and only other 1310 non-root and 350 wg bridges conenct but cannot get the other 350 non-root bridges to associate. I have seen other posts about this but no one ever posted the fix. I am running ver 12.3(8)J...

I'm getting the following error in my wireless controll software. I have an ssid that is setup for 802.1x authentication with WEP 104-bit encryption. And everything seems to be working besides is warning message.The WEP Key configured at the station ...

I have a customer looking to install a wireless network across 3 floors with full coverage on each floor. 2 ssid's are needed one for guest use and one for their business use. The top floor is where the server and demarc is located. The top floor is ...

Hello !We're using Cisco Aironet 1200 access points. We would like to use Microsoft Radius Server for authentication by Mac address.Before we use Cisco AP's everything was just fine but since we use Cisco authentication by radius doesn't work.Somethi...

I have an Cisco 877 router and I've set a lan to lan up into our concentrator at our main office. When plugging into the router via ethernet everything works well. Lan to Lan with split tunneling to the internet. The problem arises when I try and con...

I have assigned a guest WLAN to port 4 on my controller that terminates on a network physically separate from my internal lan. Since getting an ip address from my lan DHCP server won't work, I decided to use the internal DHCP feature of this control...

Dear All,I have a comapny of about 40-50 users. I'm planning to deploy WLAN instead of wired LAN. What is the acccess point that fits my needs? the company is laocted in wide appartment.Thanks for your interest,Tamer

Hello,I have a mistake in my configuration but I don't know where.I use WLSE,ACS,WDS an AP on two sites and it works well.I use 3 vlan (native 1 , voip and data)WDS and AP are 1100BPhone is 7920I need to add 2 new AP1100G, and it works well.Now I nee...

hi guys: IS there any good ways to detect if the client's computer support 802.1x(OS or adapter)?We would rather not check each client's computer one by one.Thaks for help.regards

When trying AP Radio Scan, It couldn't works. I have setup WDS and got AP Information all my AP has registered and WNM Information is Security Keys Setup. All AP are managed. Fault WDS Treshold have been enabled. I use all brand new 1100 AP with 12.2...

Has anyone tested Aironet IE with Cisco 350 card and CB21 (Cisco ABG card) on 4.0.155.5? Without Aironet IE enabled, the CB21 does not report back CCX. When I enable Aironet IE, the CB21 reports back CCX4 (I have latest driver 3.0), but breaks the ...

Hi,We have an application that is used between teachers and students and requires the use of multicast.How do you enable the aironet devices to pass on the multicast messages over the radio interface.RegardsMiron