Wireless

Is there a statement or debug command to tell how an AP is being powered? Via Power Injector or Inline power? We have Aironet 1230's deployed at some remote sites and want to determine how they are being powered.

7921 phones only support up to 40mW on 802.11a. However the wonderful LWAPP system doesn't support 40mW it supports 17dBm and 15dBm (no 16dBm or 40mW).How do you use the LWAPP system (4404-100 controllers) to use auto power and make sure they don't s...

hi,my system:1 WLC 4404 (SWv. 4.0.217.0) -> connected with LAG to a 3750 Switch1 WLC 4402 (SWv. 4.0.217.0) -> connected with LAG to a 3750 Switch125 AP 1240AG1 Voice WLAN (qos platinum)1 Data WLAN 7920 Phones Firmware 7920.4.0-03-02config WLCs:- one ...

Have preordered some 1250AG radios and are preparing to install some outdoor omni hotspotantennas with cables. Will there be enough with 2 antennas on each band if we only use one channel (not bonding)? Will 3 antennas give any advantage using only o...

When a WLC is updated causing the APs to upgrade how is this upgrade achieved?In particular, how does the AP communicate with the WLC, does it use TFTP if so does it communicate directly of through the LWAPP tunnel? I have a customer that is concerne...

I am running a 2106 controller with 1242 AP,Had them on a POE injector on the same switch worked fine, mounted them in the ceiling now the radio will not enable."error in enabling admin status". any ideas?

Ok, we just bought a new Aironet 1240AG and even though I've down a lot of basic route setups on Cisco router, I'm stumped as to how make this work.I've got an Aironet 1240 AG. I set the static Ip address on the BVI interface and went through all of ...

I am having problems locating the correct MIBs to monitor using SNMP. I would like to monitor the counters displayed on the Radio interface's detailed status page when using the web browser.I have found the CISCO-DOT11-ASSOCIATION-MIB stats, but that...

Hi, I am setting up WPA2 enterprise for wireless users with PEAP authentication, but can not get authentication server to authenticate them, and failed reason is generic "EAP-TLS or PEAP authentication failed during SSL handshake"The AP I am using is...

1130AG running c1130-k9w7-tar.124-3g.JA1, in autonomous mode.VoIP - Call manager 6x, Cisco phones only, Vlans - Open, secure data using WPA2, VoIP Vlan is using pre shared keys.Switch Configuration - C3548xl's, C356048ps, 6509 coresI have been lookin...

Hi,we have the following implementation:Cisco Access Points mainly 1200 series, Cisco ACS v.3.3, and MS Active Directory.I've

First off, a radius server is not in use. With that in mind, what is the best way to secure a point-to-point link using 2, 1310BRs?

Hi,I seem to be getting a 5sec audio delay with peer-to-peer conversations ? at first you answer "hello" wait a few secs then hear them saynig "hello" and then your eventually connected ?what could this be, i have ample signal strenghmany thanks

Dear all,We have recently decided to enable WLAN for guest users that authenticates users by redirection to WLC's virtual address (1.1.1.1).I have created WLAN and assigned management interface for it on WLC.Interface points to dhcp server that resid...

Hello,We have 2 4402 WLC's, the second one is configured as fail over.We are creating guest accounts on primary WLC. How do we use the guest account during fail over to second WLC ? (of course without configuring the guest accounts on both controller...