Has anyone used WAP3 192-bit Security with the RADIUS server to authenticate corp users using certs(EAP-TLS)?We are currently using EAP-TLS but on Meraki, it's WAP2 only. If so are there any changes that need to be made on the Radius server?All of ou...
Forum Posts
Hii have Cisco 9115 axi AP, when i plug in my switch POE, it doesn't turn on in my switch(like the port is down, but it doesn't), but in the side of my AP, i see alternate red and green ligth.See below the initial boot messages error
Which is the best Meraki Layer 3 roaming solution to use, distributed L3 or via a concentrator? What are the relative merits of one over another (apart from not have to buy some MXs of course) and when would you use one over the other?
Resolved! Bulk factory reset APs
Is there a way to bulk factory reset specific APs that are associated to a controller? Prime's config template doesn't seem to have an option for this, so I'm wondering how (both in AireOS and IOS-XE) this can be done from the controller.The only thi...
Hello Team, we are facing a strange issue that we have C9130 access points where they reboot automatically reboot for every 20 days but not all the time and becomes stable. When I checked on the AP logs it shows as below. CHBGBFRONAP003#Jan 10 12:24...
Hi,I have installed the solerwind sftp server in my window machine and i want to copy running configuration from cisco switch to sftp and vice versa.Can someone help me with the below queries please> Is Solorwind sftp server tools good to install in ...
I have an SSID that is setup on several APs across the network in different geographic locations. How can I monitor the performance of the SSID? And can I drill down to the location and individual AP level?Thanks,Gil
I converted my 3802i lightweight access point into an autonomous one running 8.5.182, gave it a management ip address of 10.136.32.50 and then rebooted it. but the console message gave a different ip address (same network but not the one I statically...
Have you experience taking too long for the client to get a IP after the posturing in ISE? On anyconnect network message history in wireless client device, it takes more than 30 sec on acquiring IP address state connecting on 9800 wlc. In aireos, thi...
Resolved! Need Help Reg Cisco 9800 WLC
Hi @AllI am trying to get the bsnApIfType from cisco 9800wlc the value returned is 5 but according to AIRESPACE-WIRELESS-MIB there is only values for the below,bsnAPIfType OBJECT-TYPESYNTAX INTEGER {dot11b(1),dot11a(2),uwb(4),dot11_6ghz(6),dot11_xor_...
The problem is the following: I have my splash page configured on an SSID and the authentication method is through a Google account. When I enter the SSID it does not show me the Splash, it shows me a series of steps to follow to connect. I have repl...
Hello,I have configured bunch of C9800-CL WLCs, it seems the trustpoint mechanism is slighlty different with a physical WLC.I associated the wireless management with one of the embedded certificates that was already existing in the trustpoints list. ...
Hello All,We have 2 WLC's. 5508- Anchor WLC (8.5.161.7)3504- Foreign WLC (8.10.185.0)I have created a mobility group and added the WLC's MAC respectively.The FW ports 16666, 16667, 97 are all open.The control path is UP but the Data path is DOWN. I t...
Hello, Since we're migrating our AIreOS WLC to C9800 WLC, the on-site team complain that with their wi-fi scanner, they only see AP Mac-Address instead of AP hostname. Do you know if there's something to enable on C9800 to keep the original behavior...
Hi All,I am currently planning the installation of a Cisco 9800-40 WLC that needs to be connected to two upstream switches for redundancy, however the two switches are not in a VSS or stack so the uplinks cannot be configured in a LAG. The two uplink...
