Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Insider User Research program

Labels

Forum Posts

Just migrated some of my users from wired network to wireless network. Both wired and wireless are on different segment.So of them still prefer to connect via wired while sitting at their cubicle and at the same time their wireless card is also turne...

jazzzz by Level 1
  • 911 Views
  • 4 replies
  • 0 Helpful votes

I'm considering deploying a wireless network between two of my buildings, the issue is that I'm in close proximity to an airport. I seriously doubt that this would be a problem (after al, why would the FCC ratify a standard for buisness use if it wa...

Placate by Level 1
  • 338 Views
  • 1 replies
  • 0 Helpful votes

I'm trying to use EAP-TTLS with a 350 client and having a problem in that the settings to enable WEP are all in ACU, and not accessable when using Windows 2000 and other supplicants. None of those setting are on the device configuration, as they are...

hkfiedle by Level 1
  • 456 Views
  • 2 replies
  • 0 Helpful votes

Any idea about QoS mechanisms on AP1230 : For instance (I prefer CLI) :- if I want to reserve 50 % of bandwith to vlan10, 30 % for vlan30 and 20 % for vlan50- If I want to reserve bandwith by protocolPlease forget the MAC add cause it is not what I a...

Mark3000 by Level 1
  • 323 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have an AP 1200 that I want to configure in repeater mode, but when I do this it stops to respond to the IP address. Traffic throw the AP works just fine, but I can’t access it via IP only buy console.(running ios 12.2.13-JA2)Any Ideas on what i...

rwedham by Level 1
  • 339 Views
  • 1 replies
  • 0 Helpful votes

I have an AP340 running VxWorks 12.04. If I navigate to the 'Manage Installation Keys' page (Setup, Cisco Services, Manage Installation Keys). It shows the device type as AP4800-E. Is this a known problem or is it a dud?Andy

Does any Access Point from Cisco support the Contention Free Mode (PCF) according to the IEEE 802.11 standard? And if yes, how could it be enabled and configured?

r.leutert by Level 1
  • 571 Views
  • 2 replies
  • 0 Helpful votes

I've tested Linksys WAP11 connecting to BR-350 and works fine, but not with AP350.Is there any configuration options in AP350 that may allow generic 802.11 connections ?I tried (no aironet extensions + bcast essid).Luciano Lima.

I wonder why i only have the option of using 50mw and not 100 that i says all over about the ap 350 model. Is there any thing i can upgrade to make it work, any one got a clue ?regards Thomas

Need to have wireless cover a 2 mile area. Installed 1230B with ANT24120, but the antenna isn't working as it supposed to do. The working range with Cisco Aironet PC-card is less than 150 feet.Any known issue/configuration/t-shooting/suggestions?Th...

bo.guan by Level 1
  • 309 Views
  • 1 replies
  • 0 Helpful votes

I would like some input to a problem. I have notice considerable slowness using 802.11/b wireless cards in a 802.11/g wireless environment. I have Cisco 1200 APs using a variety of client wireless cards.

aroch by Level 1
  • 547 Views
  • 4 replies
  • 0 Helpful votes

Please see my before topic : AP 1100 help ??because i can't read the https url that someone give me....The url want a password ??please help....

albatore by Level 1
  • 586 Views
  • 3 replies
  • 0 Helpful votes

I just received a couple of the a/b/g cards and see they have a new Aironet Desktop Utility (ADU) instead of the ACU. This doesn't include any site survey tools. Anyone know if any are expected?

mvario by Level 1
  • 387 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card