Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
what happened if I got message from my AP350 LOG as following:Network Bridge Loop: Received packet from Self destined to [AWC Mcast AP-Only]014096ffff00 on port "fec0" and How can I slove this problems? THANK YOU FOR YOUR HELP
I've read that the Aironet 1100 isn't supposed to be a DHCP server. However, I have two laptops with wireless capability and when I turn them on they connect wirelessly and get an IP address in the 169.254.147.x series with no default gateway.Our ne...
Resolved! What's the most secure WITHOUT a server?
Without the use of a server, what is the most secure way of protecting your WLAN? Aside from non-broadcast SSID, 128-WEP, MAC-filter, and Open key. I’ve heard rumors that you can use LEAP, without a server, but I don’t understand where the user dat...
Have anyone seen a problem with an aironet client not able to get the dhcp ip address? I upgraed my 1220 to 12.03T and using the ACU 6.1. The problem is happening.
Hello group,Does anybody have an experience in creating EtherChannels over 2 wireless WAN links (Tsunami equipment) terminated on Cisco switches?thanks in advance tat
I have a new C1100 series that is running 12.2(4). I am trying to get mac-address authentication to use my RADIUS Server (Funk SBR). I think I am close, but I have been close for about 12 hours now.I am using an ssid for the dot11Radio 0 inetface.....
Hello,I am trying to speed up the amount of time it take for a WLAN client using PEAP with OTP to authentication the WLAN.Currently, it can take up to 2 minutes before a user is prompted to authenticate. Is there any way of speeding this up?I know o...
I can not associate with the repeater unless the repeater is associated with the root , The repeater associates with the root for some times and then disconnect , it is not stable and I can not associate to see whats going on . even when the repeater...
I upgrade a test AP to the new code of IOS for the Aironet 1200s. Before the upgrade we were using LEAP for authentication and it worked fine. With the upgrade, I can not get LEAP to work. We are using Cisco ACS 3.1 for our Radius servers. I beli...
We have a 1220 AP with the A-band modular card and the b-band mini-pci card. Can you assign each SSID a different name in the same unit? In the setup guide for a dual band AP, they are both called "tsunami" by default. I want each band to be recognis...
Hello,i try to connect xp client with ap350 acs 3.2 and aceto the network.When i try to connect to the network ,get on the acs3.2 the error msg ,,external db authen.failed,,.For every help thanks a lot.Harald
Hello,I need to know if Cisco is officially supporting Aironet 350 client firmware 5.20.17 with DOS drivers. The software seletor tool shows 4.25.30 as official for DOSAs far as I know firmware 5.20.17 is official only for Windows versionsNot even Li...
dear memberswhich AP will support hotstandby feature, i want to provide a second AP as a backup.any details would be very usefullthanks and waiting for the solutionregard
I have questions about WGB350. Is the WGB350 supported for PEAP?- If yes, does it work with Active Directory?Are there plans, for the WGB350 to develop further?- new SW versions, IOS?Regards.Marcel
I need to encrypt client adapters and make them ready for use without the need to configure it at the client machine. Is there a way ?
