Wireless

I have a building approximately 150-200m away from my main site, which I have connected to our LAN via non-Cisco 802.11b wireless bridges. My company is located in the city and we are aware of atleast 20 other wireless networks in close proximity. Ev...

I am not having a successful time getting Linux to use the 350 MiniPCI internal card in my Dell Latitude D810, using LEAP for our network.I have tried downloading the linux drivers but that seems to be a dead end. I can't even get the install script ...

I upgraded an AP 1100 and AP 1200 to IOS 12.3(4). I am associating to the AP 1100 and the AP 1200 is acting as a dedicated WDS server which forwards authentication requests to a RADIUS server. I succesfully used LEAP and EAP-FAST authentication with ...

Hi all,Can anyone tell me if and when they would use Hot Standby Mode to provide a redundant wireless solution. What would be the problem with a second AP on a non-overlapping channel for an isolated WLAN island, or, a large overlap design where grea...

Hi,I have a couple of problems with the trend reporting in WLSE. I've selected the RF and Ethernet utilisation graph, but when I click on weekly reports it comes up with available dates from 01/13/2005 to 04/14/2005. I can't work out what's happened ...

Hi,I have enabled the AP 1200's SNMP. Understand that signal strength can be extract from awcVx-MIBs. However, I m unable to display anything. Is there any prerequisites or steps to be taken ? Appreciate any answer...Thanks in advance.rgdsFrank

I am having problems setting up WDS... on my 1200s I am getting events stating the the "AP has timed out authenticating to WDS". Also, under wireless services my wlse server is showing a status of unauthenticated. Any ideas? Are there any good docs o...

I am using Cisco 1100 series AP with PEAP authentication and IAS. I have debugged a long authentication\re-association problem down to the AP rejecting any session key length which is greater than 32! The IAS server attempts to issue session key leng...

Dear friends,I'm configuring a link between two 1310, one using a Yagi and the other using a omni. The configuration is pretty simple, without any type of special feature, like cryptography. When the bridges are near one of each other, the link is pe...

Is there a safe way to change the duplex (from half to full) on the wired port of a 1200 AP running IOS 12.3? When I go into it wirelessly with a browser I see a message that says I shouldn't change the duplex setting.Can I do it via telnet or WLSE?

Hi,I currently have Cisco 1100 AP's in my network normally used by wireless users for non voice applications. The AP's are running IOS 12.3(4)JA.I have bought a couple 7920 phones as a trial for voice over the wireless. The phones are running firmwar...

I just tried to upgrade my firmware to IOS in the AP1200, using the steps provided by the Cisco website. And now i can't access the AP using IE and the IP address. I used to be able to access it fine when I had VxWorks, but since the upgrade I cannot...

One of our offices is serviced by a single 1200 AP. It in the far areas of our office, we had seen the signal drop off. Does Cisco make some type of Signal booster or repeater?Basically I dont want to buy another 1200 if it means they will get droppe...

I have a few Aironet 1200's running 12.2(11)JA3 with WVLAN'ing. Users on one of the WVLANs complain that more than one wifi client cannot associate at a time. If the currently associated client signs off, the next one is immediately able to get on.LE...

Hi,I'm trying to get a kit together that can do all needed site surveys. I know the 1200 will work fine for indoor AP surveys, but can it also be used instead of a 1310 for all outdoor site surveys? Is it functionally the same in terms of radio stren...