Wireless

I have 2-cisco wireless brigdes that are having problems associating. The topology looks like this:cisco350WB-omni <----------> cisco350WB-yagi10.1.1.4 /28 10.1.1.3 /28root bridge bridge w/out clientsI plan to connect more bridges in the future to th...

Got a pair of 1310 running IOS 12.2(15) with external antenna, 4km apart, and 1 PC on each side.I'm just using MAC authenticate and filters with the trouble of SSID broadcasted and no local RADIUS server.What's best in terms of security config? How t...

Hello we have a number of Aironet (Before Cisco) Wireless AP's, it's the model Aironet 4800 Series Turbo DS Model# AP4800-E, and I was wondering if they were WPA 2.0 compatible and if there were any upgrade kits to make them compatible if they are no...

We are running WPA with MAC Filters on a 1100 Version 12.2.15 JAWe keep losing association to the AP for no apparent reason. To get it running again we are forced to re-seat the 350 Card or reboot the laptop.Here is a little from the AP Log. Apr 11 1...

Has anyone got any experience of all of the above. Some background - The FWSM is in transparent mode, using virtual contexts between the VRF and the main routing table to ensure relevant mobility traffic passes through the relevant security context.I...

I have a 340 series AP and have already installed the driver for my 350 series PCMCIA LAN adapter.I've checked that the AP has a valid IP (10.x.x.x) assigned to it(on our core LAN switch).I get a 169.x.x.x IP address.The Aironet Client Utility(ACU) s...

Hi,Since a was browsing through this forum I noticed that there are lots of problem with DHPC request and the AP 1200. Well here is another "simple" problemOne "out of the box" AP1231 Upgrade to IOS : c1200-k9w7-mx.123-2.JA2Configuring SSID and WEP 4...

I have 5 AIR-AP1231G-A-K9s. SW - 12.2(15)XR2. My clients which have 802.11g cards are fine. Most, not all clients with 802.11b cards constantly lose connection. Radio settings are set to either channel 1,6,11. Data Rate is set to default, only 1,2,5....

Is it possible to have my 1200 WAP automatically shut the radio off at 6:00PM and turn back on at 6:00AM

ok hopefully not to dumb a question. I read somewhere in the ordering guide for the 1230 that you need to order two antennae in addition to the base access point or access point/radio bundleIs that true for all antenna types or just the typical dipol...

Reading through the documentation on the 1200 series AP running 12.2 IOS it only explains how to create VLAN's via the CLI. Is this possible via the GUI as well?

Anyone else experience this - 802.11g CB21AG-A-K9 card goes through all the LEAP authentication, but hangs on Step 5. Finding the Domain Controller. Sometimes it just sits there for a minute before failing, sometimes it authenticates after 15 seconds...

After a write erase and a reload my Bridge boots up as an AP with the DOT110 radio shutdown and no ssid?is this normal?regards Bernhard

Hi,I'm using an IAS server as my authentication server.I have also an WLSE 2.9, i have configured an AP to be WDS , following the config guide.WDS information state is ACTIVE but in wds registration i can't see this AP registed.In wireless network in...

Can anybody explain why the Black Hole Mitigation feature changes the default 100kmicrosec beacon interval to a "slightly lower value" (usually 99 or 98 kmicrosec) ? I am rather baffled by this very slight change - where is the advantage to black hol...