Wireless

I'm installing 3 1210 access points and was wondering if I could use one of them as a DHCP device to give IP addresses to wireless laptops.

The new AP 1232AG at present covers the 5.15-5.35Ghz and the 5.725-5.825Ghz bands. Tocover the lower bands I can use the ANT5135,5145, or 5160 antennas, what can I use on the 5.725-5.825 bands, can I uae the AIR-ANT58G9VOA-N( normally used on the br1...

What requirements are there for Fast Secure Roaming on the client side? Does the client just need LEAP support? Does a thrid party card need v1,2 or 3 of Cisco certification?I see version 2 has LEAP capabilities but version 3 has CCKM capabilities.Al...

After upgrading to the new 12.3(2)JA firmware, my clients are no longer able to receive IP addresses from the DHCP server on any VLAN other than the default VLAN. My environment is a Cisco 1200 with 2 VLANs. There are two SSIDs, OPEN1 & OPEN2. Neithe...

I tried to upgrade and it failed now i am getting this msg.Testing DRAM...(press <esc> to bypass)DRAM OKPower-on reset.Copyright 1996-2000 Cisco Systems, Inc.Copyright 1984-2000 Wind River Systems, Inc.System ID: 00409641DC8CMotherboard: MPC855 50MHz...

Hello,I've been trying PEAP Authentication with ACS and RSA, in order to try PEAP-MSCHAP and PEAP-GTC and I have doubts on three aspects.The first, is related to server certificate authentication : On most PEAP supplicants you have the option to not ...

Hi for all !1) Does Aironet1100 support dot1x guest-vlan ? how ?2) I ve done RADIUS based VLAN (ACS 3.3), with one SSID and 4 VLAN (only one is associed to SSID)the Network EAP and VLAN identity based assignement work correctly.In ASSOCIATION menu , ...

Dear Sir,I have a WLSE 1130 with software version 2.5 running in my current network. I managed to discover the APs installed in my network.I used Microsoft Paint to draw a diagram of the floor plan of my building and save them in .jpg format as the W...

I havent had to setup any repeaters in the wireless networks I have designed..In this specific case, I can think of using a repeater to establish a wireless shot between four locations. Here is the scenario..Site1---Site 2(Omni)----Site 3(Repeater)--...

According to the Quick Start Guide the Aironet 1200 Series Access Point I just purchased should have an antenna that I can fold out if the device is used in a horizontal position. Is this antenna standard? Or is it only by special order? The back of ...

I´m from Sweden and i have a 1km wireless link, it has been up for almost a year with Dlink stuff and two 15dbi directional antennas.I use a dwl-900ap+ as a AP and i have used a dwl-520+ pci card in windows 2000 as a client,it has been rock solid.I c...

Problem:I currently have a contractor that has presented several solutions regarding a WLAN project I’m working on, though not with a great level of clarity. I don’t feel that I’m getting complete information so I’m hoping you may offer a generalist ...

I'm setting up a WLAN using Cisco 1200 access points. I'm using Cisco ACS 3.3 for 802.1x Radius authentication and authenticating using Active Directory. I have a Cisco Aironet CB21AG client adapter working perfectly with LEAP and no authentication. ...

I have interesting problem with Aironet 350 PCMCIA Adapter. It is used with Linux Slackware 9.1 in PC104 stack. It works fine when there is video adapter card in the stack. But once the videoadapter card is removed, the system reports following error...