actually we are planning to get new 9800-L , is bellow access points supported by 9800-L Wireless controller , and if it is supported is there any feature and version limitationAIR-CAP3602I-E-K9AIR-CAP3702I-E-K9AIR-CAP3602E-E-K9AIR-CAP2602I-E-K9AIR...
WLC-9800-40Sw: 17.9.3Hello, I have a client issue with a user. He dissconnects very often and a radio trace and clientinfo shows this:Any suggestions what to check ?regardsJohann Folkestad
HiWe're using Certificate based authentication for our Windows machines to connect automatically to our internal Meraki SSID (with RADIUS/802.1x).The certificate is issued to the client PCs using a GPO and from our Certificate Authority/AD Domain Con...
Hey everyone this has been bugging me crazy. How can i know which Meraki AP is suitable for how many users ?For example how can i know how much users is suitable for an MR 20 AP ?. any checklist or something will be usefull.
Hi,I was investigating wifi issue forthe users , they cant get dhcp and noticed some discrepancy in the config , I am not sure if this can cause. Can you help with expert review? So, Wireless/AP/General/IP config dhcp shows 10.2.0.1, mac address of t...
I have a 3504 HA pair of controllers which have 100 registered APs on them currently and they are licensed for 150 APs. They are a mix of 2800/3800 and a few 9120s. Recently we purchased a few more 9120s. They are all being added to the same Vlan...
I'm trying to get the details for the Cisco C-ANT9103 on Cisco Prime/WCL. Is there an option on Prime to get the details (serial number) of the antenna connected to the Cisco C9130AXE-E Access point, As it is in production and running, I have only th...
So i have the following problem, i changed the access point from lightweight to standalone and configured it with a static ip which i can ping. When i try to access the web gui i get the response "err_connection_refused" from my browser. I tried seve...
Hi, If create Internal DHCP on C9800 for Wireless, It also distributes IP DHCP to wired clients in same vlan. Can it be disabled IP DHCP to distributed to wired clients? Thank you so much.
Hi all, I'm trying to find the maximum range/distance that an MR86 with two MA-ANT-25 antennas can reach. I haven't' been able to find anything in the documentation. thanks,
Hi all,I have some questions about LWA, I configured everything and I get login page and can login and everything works fine. The problem is that I don't want to use 192.0.2.1 address for guest portal, when I set Virtual IPv4 Address to guest-wifi.co...
Hello everyone,I am trying to make my AP C2600 to join to my exiting Virtual Wireless controller which has already controlling over 10 units. They are c2700 series.The AP C2600 was used and connected to other Wireless controller before but it was dec...
Hello!Im upgrading some of my Cisco AP's to IW9167-EHB's and the AP is stuck in a loop.I'm getting the following errors:[*08/11/2023 00:34:09.8578] CAPWAP State: Discovery[*08/11/2023 00:34:09.8588] Got WLC address x.x.x.x from DHCP.[*08/11/2023 00:3...
Hey Guys, i just want to have a quick check what is the best way to upgrade the 3.8 CPI (running on VM) to 3.10.x After some good reads from cisco docs, i understand that only way to upgrade is to create a new VM, install 3.10 and restore the backup ...
Hello Team, We have connected C9120AXI access points to WS-C2960X-24PS-L switch. It is consuming 30 Watts of power. Is there any way to reduce the function of AP so that it can consume power less than 30 Watts? Below is the output for Show Power Inli...
