Hi everyone, I have a question, what RF software have a database with Fluidmesh AP and antennas??? I need have a Point-to-Point design in mining industry, and I don't know a software compatible with Fluidmesh equipment. Best regards.
Forum Posts
Hi, I have around 10 Cisco AIR-AP1042N-E-K9 that are already attached to my WLC 2504. My first question is: the way I can check how many clients/users are connected to one of the 10 AP My second question is: Is there a limit max of users per AP. I've...
I just found limit maximum wireless client count per wlan,and per radio wlan.Is there possible to limit maximum wireless client count per ap?
Buongiorno,sono venuto in possesso di un controller e 6 ap dei modelli scritti in oggetto.come devo fare per aggiungere il primo AP al controller?Non conosco bene la programmazione di prodotti Cisco ma piacerebbe molto imparare.
In the MR Product Intro course (login required), you’ll learn all about the Meraki MR, including ideal use cases and problems you can solve with MR access points. By the end of this course, you will be able to: Describe the scope of the Meraki wirele...
I WOULD LIKE HELP, SINCE WE CURRENTLY HAVE CREATED TWO WIFI ONE FOR ONLY WINDOWS AND MAC OS AND ANOTHER NETWORK FOR MOBILE DEVICES BUT WHEN WE ACTIVATE THE POLICIES SO THAT ONLY PCS CAN BE CONNECTED IN A NETWORK, SOME MERAKI DETECTS THEM AS MOBILE DE...
I have two access points Catalyst C9115AXI-E connected to a virtual wireless LAN controller (vWLC). One of these two access points reboots every 4 hours 17 minutes and 10 seconds, which is every 15'430 seconds (+/- 5 seconds). And this, consistent ov...
Hi team,I'm wondering whether it's needed to install APSP1 and APSP3 at the same time for the 17.9.3 release.From what I read it's not explicitely stated in the download area, release notes or the "Recommended Cisco IOS XE Releases for Catalyst 9800 ...
Hi board,I'm confused regarding the IPv6 RA guard on the Cisco 9800 WLC.First of all - when coming from AireOS, it's not clear from the documentation where the IPv6 RA guard is enforced. On the AP or on the WLC? Secondly, the documentation is pretty ...
Hello,I have a WLC 2504 and it has the following licenses:I currently have 25 APs installed but I want to add an additional 15 APs.The license of 25 APs is used, but in the image it can be seen that I have 2 licenses plus one of 15 APs and another of...
Resolved! Wifi controller errors c9800-cl
Good afternoon.I recently upgraded our c9800-cl to version 17.9.3, hoping to get rid of some old problems, but only got new ones.Some of our clients are losing connection for unknown reasons and need to be reconnected.We have a 1000 square meter offi...
It's not appearing available to install yet, but I discovered the release notes paging through firmware versions.Important noteWhile Meraki APs have traditionally relied on UDP port 7351 for cloud communication, and TCP ports 80 and 443 for backup co...
I am running a Catalyst 9105 access point with EWC 17.6.1. It has one SSID configured and associated with both bands. With this setup, I observe frequent client disconnects. For my iPhone SE 2, they often happen right after unlocking the device, but ...
We have a WLC 5520 that suffered a power loss on Friday. Since then the unit has been inaccisble via its standard IP Address. Upon gaining console access to the device it appears to be idling at the Configuration Wizard/Autoinstall. Here are the Erro...
So if I statically assign DFS-required channels on my APs, what happens when radar is detected on that channel? Will the AP just stop transmitting? I haven’t been able to find any real information on this. Thanks
