Hi All, I have two Access points that keep restarting forever, when I connect a console cable I found the following lines. [*02/05/2021 05:04:30.8873] chpasswd: password for user changed[*02/05/2021 05:04:36.8354] systemd[1]: wcpd.service failed.[*02...
Hi, Im trying to setup a 2802i to do a AP on a Stick Survey. I converted the AP to Mobility Express 8.10.152. I went through a fresh setup and assigned an SSID to both radios. It is only broadcasting from the 2.4.I tried creating a new SSID and assig...
Hello Guys,@balaji.bandi @Sandeep Choudhary @Rasika Nayanajith I got a working WLC connected with interface in vlan 1 of switch and on WLC its configured without vlan. I need add another virtual interface in other vlan. I added vlan identifier (v...
Hi All,We are trying to make our Corporate Wireless at HQ to work again. When I undock my laptop from docking station, it is not automatically connecting to Corporate Wireless. It works when I copied same configuration.xml file on the system folder ...
Hi SSH is enabled under wlc 9800. Username and password are created at the controller, but we still cannot logon to AP9117. It shows password authentication failed. Please see the below configuration. Not sure if there are other configuration that we...
Hello, I have two aps model 2802i, my problem is that my second access point can not to join to mobility express controller, both have the same firmware version 8.10.151.0, When I run a debug command in the controller, I see a errorThe IP Address fro...
Hi, Network access control, NAC, is solutions to support network visibility and access management through policy enforcement on devices and users of corporate networks.I can get some of info of NAC as below. Firewall can also do that. what is differe...
I have a 9800-40 running 17.3.3 I used to be able to get the BSSID for each WLAN on a 5596's Access Points with the following: snmpwalk -O b -v2c -c <omitted> <IP of WLC> CISCO-LWAPP-AP-MIB::cLApRadioWlanSsid<instance of Access point e.g. .20.22.157....
Hello everybody!Wlc 5508 controller There is such a problem:A client stuck to a point with a good signal, after turning off this AP, moves to another AP with a worse signal.But after turning on the first point, the client for some reason does not ret...
Hi All, Devices: Cisco Prime, ISE, WLC 5520. I have one business case, where I need to restrict amount of data per wireless client, because of limited amount of data and because it will be open wifi for customer. Do you have any idea how to do it wit...
Hi everyone, I am unable to have my AP c9130AXi to join my WLC c9800-40. I defined the controllers IP statically and here is what I am getting: [*07/28/2020 05:22:17.2525] CAPWAP State: Discovery[*07/28/2020 05:22:17.2600] Discovery Request sent to ...
Hi, pretty new to this so please be gentle. We have a WLC that we setup for wireless Mac authentication on the local WLC database. I want to move this list of mac addresses to ISE. I am following a tutorial which says to create an endpoint identity g...
Hello everybody! WLC 5508 controllerWhen collecting debug (debug client <mac>) I ran into a problem: it breaks the ssh session.Before debugging, I enabled config session timeout 0Please advise how to solve the problem.In Putty, there are no settings ...
Folks,I have recently purchased a Catalyst C9117AXI-EWC-B access point. I have been slowly finding out what this does. I have read almost everything that has been written about these but I have a couple configuration questions. First I see something ...
Hi,Quick question, when assigning vlans dynamically to wireless clients based on different radius profiles, are dotq1 tagging required on the access-points?
