Hello, I've a new installed C9800 Wifi Controller GigabitEthernet1 is for Management and configured: interface GigabitEthernet1 no switchport ip address 10.2.99.250 255.255.255.0 negotiation auto no mop enabled no mop sysid Gigabit Ethernet2 is...
Forum Posts
I simply might reading the release notes to early, but: hmm Cisco...WLC 9800 16.12.7 s out, the following is "new" or "changed"What's New in Cisco IOS XE Gibraltar 16.12.7There are no new features in this release.Open Caveats for Cisco IOS XE Gibra...
I'm stuck between two - the 2504 and the 5508. I know the 5508 will be a larger power hog being full 1u form factor, but I've read it's got a faster backplane and will do 8g simultaneously (vs 1g on the 2504).The 5508 is also more readily available o...
Resolved! Schedule Transmission on Catalyst 9115
Hi All, I am wondering if there are possibilities to schedule the transmission of WLAN on the Catalyst 9115. The documentation I found does not give any hints.Reason for the question: I would like to switch off the transmission during sleeping time t...
How to purchase latest standalone update for AP3500 series.Want update standalone software buth cant download update
i want to make a wireless internet access in my camping place.... the area is 700 meters.... which product is best for me ?what about Cisco Aironet 1552E-E-K9 Outdoor AP ?how long distance will i get for Cisco Aironet 1552E-E-K9 Outdoor AP ?"Cisco Ai...
Hello,I have a pair of very EOL WLC 4402s that I am trying to set up for my church. Unfortunately one of them is running a slightly older version of code and will not let me enable them to allow APs to connect. I need to enter the following commands ...
Hi I have a couple of 1810w Access Points, that will not join a controller. I have may that do. The error is below Controller Version: 8.5.161.0CAPWAP State: DiscoveryDiscovery Request sent to 62.254.78.65, discovery type STATIC_CONFIG(1)Discovery ...
Resolved! Native trunk vlan
Hi All, I am having a problem discovering an AP in WLC everytime I configure its connection in the switch as trunk native vlan 306 which is I think is the standard. It only works on switchport access vlan 304. When I run switchport interfaces trunk, ...
Hi Team,I have configured Air1832I mobility express with 1 AP, Now I want to add more 2 AP how to add this ap on Wireless LAN controller,Can I upload previous AP config backup on added new AP .Please guide
Hi all, I am unable to run any command on Cisco Aircap 2702i.After "enable" command, all other command returns with "% Invalid input detected at '^' marker."I tried conf t, configure terminal, config ap etc. all the commands but no luck.please help. ...
Resolved! WLC 8.5 and DHCP Proxy
Hi, I am running WLC 8.5.182.0, and for most small VLANs we are using the Internal DHCP Server which is adequate, but not ideal. For a larger VLAN, it appears to be possible to set "DHCP Proxy Mode" to 'Disable' on a per-interface (VLAN) basis, and t...
Hi everyone, I'm trying to understand the logging messages of an Cisco AP C9115AXI, but it is very difficult to interpret. Is there any documentation explaining the meaning of each message? Thank you!
Resolved! Remove EWC image from AP
I want to convert a previous EWC AP back to lightweight.I've done ap-type capwap, but show version still tells me the AP is EWC capable. Does anyone know how I can make the AP lightweight mode only?AP Running Image : 17.3.4.154Primary Boot Image : 17...
Resolved! AP ios version is same as wlc
Hi Please see the below table and its link. The first column is wlc version and third column is supported APs. AP ios version always follow wlc version once joining to wlc Why it list second column which is AP IOS version? What is that mean? Thank y...
