Hello, I'm trying to use the external captive portal service mg.backloop.biz for sponsored guest access on my EWC on 9115 Catalyst AP but no redirect happen for guest user. Attached the screenshot of the configuration used. We only need to open the (...
Forum Posts
Wi-Fi standards change quickly and after some time your measurement devices can still do wireless surveys for design and tweaking, however when a new Wi-Fi standard comes out you can't capture the newest frame types since you need hardware to support...
Hello,i want to use an AP Cisco Aironet 1242 Access Point (AIR-LAP1242AG-E-K9) as a bridge.But the device doesnt connect to my fritzbox. I get the following errors: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from c852...
Hello,Are there any good ressources to help in the creation of a splash page that will allow authenticating users in an Azure AD?I've seen this post https://community.meraki.com/t5/Wireless-LAN/Configure-a-splash-EXCAP-with-with-sign-on-in-Azure-AD/m...
Hi Everyone,We have an existing Wireless Controller(AIR-CT5508-K9) in one of our Data center and this controller services 60 AP spreadout accross six different sites/ offices.Note that the existing data center where the controller is located will be ...
I'm using a Cisco WLC (v8.10.171.0) and have a couple of SSIDs, one which uses 802.1X certificate authentication (EAP-TLS) and another which uses WPA2 Enterprise with MAC filtering against a RADIUS server (not ISE).This is more of a query than an iss...
Resolved! Meraki WiFi Offline Clients
Struggling to find an answer on this one. Does anyone know how long a Wireless Client should still show for in the Clients list after it has gone offline and is there a way to change the duration? Struggling to find historic data at the moment.
Resolved! Mixed AP models on 9800?
Hi,is there any compatibility matrix which AP model can be managed by 9800 controller? Does a 9800 controller can only handle one kind of access point at the same time, e.g. can a 9120AXI and a CW9166i be attached to and managed by the same controlle...
Resolved! MR36H - Security screw "SKU" ?
So ... lets say ... ehh ... someone(tm) "misplaced" around 4 to 5 hundred of the included screws for the MR36H.What "SKU" should I go to my local hardware store and buy ? (Its only the small security screw Im interested in here, dont care if its torx...
Hello I can´t see the Meraki CW accesspoints in the "Wireless" - "Radio Settings". I can see tehm in the "Wireless" - "Accesspoints"-list.Anybody with the same issue?
Hello, We have Catalyst 9800-40 WLAN controllers and 90 Catalyst 9120AXI access points. Three weeks ago we upgraded from 17.3.3 to 17.3.4c. But instead of fixing a bug, it got exchanged with a new one: Since then all the WLAN clients can't communicat...
Resolved! Guest SSID External Radius Issue
Hello,I configured a guest ssid with external radius on Meraki.I entered radius ip and take capture from radius side there is no authentication radius from Meraki.Any ideas?While troubleshooting the issue I realised that there is 2 different url for ...
Resolved! Get wireless guest client session length
I am in need of gathering some information on how long the sessions are for guests connecting to the guest wifi. I'm very surprised that this isn't something that I can easily find. We do not have Cisco Prime and since the users are not authenticatin...
Hi We are looking to perform an "AP on a Stick" survey at a new site using an MR44 access-point. However the site currently has no internet access. We could get the survey engineer to provide a 4G router + PoE switch. However, I'd like to know, if we...
Resolved! debug capwap not working
Hello , can anyone please help me out to configure my access point : AP>en AP#debug lwapp console cli debug capwap console cli AP#config t AP(confg)int fa 0 AP(confg-if)ip addr <addr> <mask> (same subnet as that of the laptop) AP(confg-if)end ...
