Couple of questions for the community.1. I have a core router that is handing out IPv6 addresses to APs. The 9800L connects to the core router. All is working as intended.Since the DHCP pool is on the router, what prevents someone, besides physical...
Forum Posts
Hello Cisco WLAN experts,I have several questions to You regarding the following output from a 3802-AP on a 5520-WLC running V8.10.183.0show ap auto-rf 802.11-abgn ZOM-AP534 Why does the output contain "0" for Channel ?Why is there no time stamp in "...
Hi!Which Indoor APs are the same or very similar to each other in indoor and outdoor casings, such as the MR12 being the MR62 in a Outdoor case, or the MR16 being the MR66?Thanks!
I have what would appear to be a simple lan to lan vpn.I have enabled: sysopt connection permit-ipsec.The remote site works as expected - without the use of any access-list assigned to the inside interface for vpn traffic.The local site will not oper...
Hello everyone I've read several post on theis forum regarding MAC Flapping in a Wireless Network but I haven't seen anything regarding Mobility Express and a single router with ethernet switch modules. When the issue occurs it causes some clients to...
Running a network for a public library and when we upgraded to Meraki Wi-Fi 6 APs everything went very smoothly with one exception: a few of our patrons with laptops running Windows 8 are unable to connect. I'm fairly confident that the issue is Wi-F...
Resolved! C9115AXI-EWC-E Mixed with AP 1852i ME
Hi all we have an ME deployment with two1852i now we bought 4x C9115AXI-EWC-E can you tell me if its better to create the Ewc new deployment and then join 1852i as “members” of the new “cluster”? ( assuming upgrade to 8.10 on the ME) Are they com...
Hi all, I am quite new to meraki solutions... and looking to deploy few Meraki AP (probably MR36 or 28 models). The client has some specific requirements below: 3-floor building each floor will have their own SSID (such as 1st floor - Sales; 2nd floo...
AP#debug capwap console cli AP(config)#interface BVI1 AP(config-if)#ip add 172.30.30.2 255.255.255.0 AP#archive download-sw /force-reload /overwrite tftp://10.0.5.137/ap3g2-k9w7-tar.153-3.JF15.default -----Premature end of tar fileERROR: Problem ext...
When i tried to change the channel it says forbidden what should i do
Wireless firmware versions MR 29.6 changelogImportant noteWhile Meraki APs have traditionally relied on UDP port 7351 for cloud communication, and TCP ports 80 and 443 for backup communications, with MR 28+ we are beginning the transition to using TC...
I am wanting to disable the 2.4GHz radio setting on a MR33 AP. I am on the Radio settings section and don't see the AP listed. The Edit settings... (blue) is also greyed out. How am I supposed to change the radio settings when I don't see the AP list...
Hello all,I have a 9800-cl 17.9.3 in use and have a problem with the dot11k roaming list.I am missing an access point in the roaming list.Output neighbor scan of the AP "WZ-AP":687d.b419.714f (BM-AP) 1 140 20 -57687d.b419.06af (TE-AP) 1 116 20 -67687...
We are excited to take the next step in the Cloud Monitoring for Catalyst journey by extending monitoring capabilities to Catalyst Wireless! As a Catalyst Wireless LAN Controller and Catalyst Access Point customer, you may be eligible to participate ...
Dear team,I have read different opinions, however, I have not found a consistent answer.According to the documents of Cisco. It is mandatory to have a DNA Center appliance in order to deploy the Cisco embedded WLC on a 9300 Switch. My scenario is the...
