Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
hello friends, one question, can a catalys 9100 AP be joined to a Mobility Express 2802, is there a compatibility table? Thank you
Resolved! 9800-40 Change AP name bulk mode
Hi everyone,does anyone know how to change AP in bulk in a 9800-40 ?this is the first one i'm touching , i'm so used to 5500 series and how easy it is to do that "change ap name "new name" "old name" and that's it, now in 9800 I just can't find a way...
Hi!I have a wifi router model DPC3928S and in the last week the wifi module was completely turned off, I don't know if someone messed with it or if it was the router itself.The "wireless" light stays off, I click on the button where it says "on/off w...
Dear all,Can you please help me with troubleshooting this problem?I have sometimes clients with HP laptops WIN10 which have problem with upload sppeed on WiFi.They are connected with full signal near AP on 2.4GHz or 5GHz band and have problem with hi...
Resolved! Wireless controller 5508 and AP2802
Dear FriendsCurrently, I have a case Please help meMy laptop uses the ax201 card. the laptop can access the wifi through 802.1x. But when I used it for about 1 hour, then it automatically lost the connection.Thanks
Experts, please help to analyze this problem, Windows can access the Internet at first after booting, but after a few seconds, it will be unable to access the Internet.Windows11 cannot connect to the network for a short time after using Cisco wireles...
Hello Fellow Networkers, I need some guidance on possible issues that are leading to an "insecure Wifi Connection" message(Attached) on Cisco Deskpro kit screens and a DX680-Tandberg screen when connected to the corporate Wifi.Below are some points t...
What do i need to do to solve this error Error in Screen shot
I have a few 2802 APs up and running, however "show license summary" shows "No Licenses in Use" It could take 20 - 30 min or more for them to show up. Is there a way to force them to be displayed? Thanks!
While reviewing our organizations WLC.s for best practice I notices that some of our sites have the guest SSID mapped to the management interface. Per the 8.5 config guide - Do not map a guest WLAN to the management interface. If the EoIP tunnel brea...
Hi All, Having issues with my 2500 series controller. Access points will disconnect from the controller and not re-connect until I set the controller date to be within the set period that the access point seems to have set on it. Example debugging lo...
We are testing a new set of WLC 9800-L in HA. running on version 17.3.4c. 2 Mobility peers is configured and in UP state (when HA standby node is down) Once the standby node is up one of the tunnels go down, and cipher changes from TLS_NUM_RSA_WITH_...
Resolved! iPhone needs long time to connect
Hi,we´ve a SSID with 802.1x authentication. Windows Devices needs a little bit time, but works fine.iPhones need two tries to connect. On the first try you can see nothing with debug client <MAC>it looks like the iPhone do nothing, but on the device ...
Hello,Has anyone here had any issues with the Intel 9560 wireless cards while trying to connect to an 802.1x network with certificate? Using version 20.xx of the driver works fine which goes up to version 20.120. However, something must have changed ...
Hi is there anyway that using mobility express on AP’s it would be able to route traffic to two different networks. At the moment the AP’s have a (corp) SSID and are on a 10.1.1.0/24 subnet with a default gateway of 10.1.1.1 which is the core rou...
