Resolved! Converting a 1100 AP to LWAPP
Hello,is it possible to upgrade (or downgrade...) a 1100 ap to LWAPP and use them with a 4400 WLC ?Thanks in advance.RegardsMassimo
Forum Posts
I have a CAP2602i that I would like to convert from lightweight to autonomous. Is this possible as with the older APs? I'm following the instructions for the older models http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrad...
Resolved! 2602i lightweight to autonomous issue
I currently have a 2602i access point that I need to load autonomous image ap3g2-k9w7-tar.153-3.JAA.tar on to, with no WLC. I have already tried the steps from the following links...http://www.cisco.com/c/en/us/td/docs/wireless/access_point/conversio...
Initially I tried to do a hard reset but it didn't work because there were still errors and the access point wasn't working properly then I tried to connect the access point with the internet but the lights are green and red,does this indicate that t...
Tonight I was supposed to swap in our replacement/upgrade WLC. We are upgrading from a 2504 to a 3504, and this week I was able to mirror the configs (minus teh few newer feature differences and the mgmt IP).So I get here, I powered down the old, pow...
Resolved! how to remove firmware Cisco AP 2702i
I want to delete all the configurations in the Cisco AP 2702i device so that I can load the new firmware to use as before, how do I do it?
Hi, We have several Cisco 7500 flex WLC, 5508 WLC, 3504 WLCs forming EOIP tunnel with the anchor WLCs in our network.. The anchor WLCs are of models 5508 running on version 8.0.152.0 and 3504 WLC with version 8.5.131.0. We are planning for a desig...
Hi , I am newbie by for CISCO WLC , I need to upgrade reason by audit check so I will upgrade the WLC to the the stable version from 5.8.x to 5.10.x all of (APs 300) unit use Flexconnection , The access point models support were check no worry ab...
We are seeing Bulk status as "in progress" for more than a day.controller model : AIR-CT5520-K9Version : 8.3.143.0 checked and found nothing related to Bug. Need your suggestion on how to fix this.
Hi,wlc model 5508ios :8.5.135.0AP Model:3700/3800/2600AP-Mode: Flex connect We have configured the flex group in our infra.Due to link flaps the AP's disassociates from WLC and joins back to the wlc.But it is not joining to the respective flex group....
I am trying to get a better handle on data rate settings. Looking at the guide (https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-2/config-guide/b_cg82/b_cg82_chapter_010111.html) I can understand the categories as described:disabled —Clie...
Resolved! Foreign controller 5520 with 9800CL as the Guest-Anchor will an 3502i off the foreign be compatible?
We are configuring a number of sites to come back to our data center for guest via auto-anchor. One site still has 3502i access points. If we were to use a 9800 controller as the Anchor would the 3502 (foreign 5520 HA) be compatible until we can repl...
Hello all,someone has find a way (OID) to monitor by SNMP WLAN Client Count for WLC 9800?For AireOS it was simple to get that value, knowing the OID; so for each WLAN it is possible to know how many clients are connected. For WLC9800 I haven't find a...
Hello, I found WMIC 3201 shut down its wireless in -20℃ (environment temperature), and its internal temperature is at -2℃. I need to modify the configuration to let it work in at least -30℃, but I don't know how to do. Please give me some suggest...
Resolved! Flashing and Moving Red Light in AP
Hi, I converted the AP into Lightweight and currently it is not connected to any WLC.Need to know if flashing red lights which are moving from status,ethernet icons are due to the fact that AP is not connected to any WLC? Also need to confirm that l...
