Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello,I've been using a Cisco 3702i for about 2 years at home now and it's been really good. Today I've updated the firmware to the latest and I was wondering if my config looks optimal to you? Mainly around the 5Ghz speed/performance as I'm set to...
HI GUYS, i have following design and need to ask below question:-Deployment of access point inside a rugged environment e.g. warehouse, we select the access point based on site condition. W3702-2E-x-K9Access point with four antenna connectors: 2 on ...
Getting this error when trying to upgrade to Mobility express. Tried different version and always getting the same error. Image transfer complete.Image downloaded, writing to flash...do CHECK_ME, part1 is active partupgrade.sh: Error: image not found...
Resolved! cisco AIR-CAP3502I-A-K9
Hello guys, One question, I want to know which country code I must choose to register my AP cisco AIR-CAP3502I-A-K9 on the WLC? The controller was set up to use the following country code:But the AP cannot register. Can someone help me with that? th...
Good Morning All, Hope Covid is treating you well. I am currently looking for a way to create a .csv file to create a contact list for the local phone directories. I would like to upload it to the cisco 8821's by bulk configuration. Has anyone ach...
Resolved! VLAN issues over wireless bridge
I am using aironet 1140's in autonomous configuration to create a wireless bridge for vlan's 1, 5, 10, 15. The problem i am having is the client access point is failing to pass anything but vlan1 through to the client side network. from the client si...
Document states DHCP option 43 helps AP to associate with the WLC in another subnet network. Since APs are configured with static ip address and WLC ip address, why these APs need option 43? In real network, APs also can work well with WLC in differ...
Hello !Regarding the following:NAME: "Chassis 1", DESCR: "Cisco C9800-40-K9 Chassis"PID: C9800-40-K9 , VID: V03 , SN: TTM235208EXNAME: "Chassis 1 Power Supply Module 0", DESCR: "Cisco Catalyst 9800-40 750W AC Power Supply Reverse Air"PID: C9800-AC-75...
I am currently in the process of implementing ISE posture assessment on wireless nets. I am seeing an issue when clients connect and posture status goes from Unknown -> Compliant. The CoA sent from ISE to WLC is failing due to 'NAS Identification M...
Hello,I have a problem when I want to update my AP1832i.In Web, impossible to go through "Cisco.com" and "HTTP" and in TFTP nothing happens.In cli, I have this error: I want to go from 8.5.140.0 to 8.10.151.On my TFTP logs I only have the file "versi...
I have a problem with my Catalyst 9800 L-C.My 9800 had some configurations then i decided erase that config with the command factory-reset allLater my 9800 reboot but when my 9800 started i can see my 9800 in rommon mode. i wastrying initializar wit...
Hye guys, I need an outdoor AP that i can corner mount that will support two differnt directional antenna's. I have a large metal clad building and need to get WIFI on the outside to cover 2 sides of the building like north and east or west and south...
Resolved! Add to disabled client WLC 5760
Hello, I have been able to add a MAC address to the disabled client list in my WLC. I was able to do this under Configuration -> Security -> AAA -> Disabled Client. I have tested this and it does provide the desired results however, now I am trying t...
Resolved! WLC SSID Interface
HiI ahve notice that on our coporate WLAN the Interface is Dummy why is this and what is the purpose of the Dummy Interface it has a non routable IP Address and is assigned to a vlan that isnt present anywhere else in the network, there is a interfa...
Resolved! Cannot upgrade 2504 WLC with new OS
Hi there, i got a cisco 2504 WLC with OS version - 7.0.112.56. when i tried to upgrade it to new OS , it gives below error. (Cisco Controller) >transfer download start Mode............................................. TFTP Data Type...................
