Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! DNAC in Wireless Deployments
Hello experts, I have a customer who is planning to setup a new pair of WLCs (9800-40) and about 260 APs. Furthermore, 1 xDNAC & 1xISE appliances have been also ordered with Wireless devices. Now, I'm a bit confused about this and I don't kno...
I have a user who just upgraded to an iPhone 13. She installed the Jabber app and tried to login like she did on her iPhone 11. She is getting the attached server error. Please advise how I might fix this?
I have since tried to access downloads for Cisco ios images..Unfortunately I am required to find partner who sold me the device, an the worst thing is, I can't even use the device Serial number yet it is genuinely a Cisco device...How else can I gain...
I have a small AP network running that has been running quietly and happily for a couple years. Recently one of the AP1815i-B-K9 failed and all that I could lay hands on quickly was an AP1815W-B-K9. It appears to come up normally and appears in the M...
Ladies and gentlemenI've got a problem here. For unknown reasons, the controller is 5520 while it's version is 8.1.123, and it's an old device. Recently, I found that the portal authentication we did ourselves cannot automatically jump after linking...
Access Points disjoins and joins the WLC frequently. It's a new AP here are the logs that were observed. %CAPWAPAC_SMGR_TRACE_MESSAGE-5-AP_JOIN_DISJOIN: Chassis 1 R0/0: wncd: AP Event: Session-IP: *************************** CAPWAP DTLS session clos...
We have issued related to AP bandwidth performance too low. Scenarios Cisco Aironet1832i convert to the controller ( Cisco Mobile Express) and other AP joined controller as well. We try to test bandwidth from AP to provide SSID and got bandwidth ar...
Resolved! Sector antennas for MR84
I have never set one of these up before. I need this to provide almost a strait line service between 350-400ft out from source to a starter shack on a Golf course.The Sector antennas make the most sense for this setup. Should both the 5Ghz and 2.4Ghz...
Resolved! C9800 and Firebox
Hi Chrome can access WLC9800 without any issue, Firefox cannot. Please see the below. It used to access it. Dont know what happen. The below info is different with what we saw before. In the past, when visiting 9800, we got a warning saying accessing...
Resolved! MA-ANT-21 hardware datasheet
HiI'm unable to find details of the MA-ANT-21 hardware. Specifically, what kind of connector is required for an extended cable between an AP to the antenna.The documentation says that is an N-Type connector, but it doesn't say male or female plug.Wha...
Resolved! 1142 APs not joining with 2106 WLC
Hi, I have a 2106 wireless lan controller and two 1142N-N-K9 LAPs. I am building a lab and am trying to get the APs to form a CAPWAP tunnel with the controller, however, this is not succeeding. So far the APs receive IP addresses from the pool config...
Clean Air is showing disable on Cisco 9130AXI AP when using it in a dual 5GHz on (SLOT ID 2). I was able to manually change it to enable but after sometime it will revert back to disable. I check the WLC and Cleanair is enable. This is only happening...
Resolved! Wireless and wired device in 802.1x
Hi We have Wireless and wired devices which need 802.1x authentication via ISE. We can see wireless authentication in ISE ( under Operations ----> Radius -----> Live logs) but cannot see wired devices authentication. Is this because wired device has ...
Hey Meraki Community,I have a feeling there is a simple explanation here but want to ask the gurus. Customer asks me what the 293 hidden SSIDs are showing up under the Rogue. I checked and indeed Meraki states these are recently seen on the LAN. Howe...
Hello,The power injector I am currently using (Model: DPSN-35FB A) has a blinking green LED for AP Power and a solid green LED for AC Power. I'm not sure if this is supposed to happen or if there is something wrong with the power injector. Appreciate...
