Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi,I have C9136I-ROW joined to the 9800 controller os 17.12.5.It is working fine inSlot 0 : 2.4Slot 1 : 5GHzSlot 3 : 6 GHzI can disable/enable all these three but the problem is for slot 2 that is disabled by default and I cannot enable it, I tried t...
Hello !Could you please tell me if anyone tested EoGRE tunnel between 2 C9800 ?The reason behind is that " -The Mobility Tunnel between 2 WLC's transports only the data-plane (client IP packets) and client context needed for inter-controller roaming—...
Hi all Is it possible to integrate an Azure hosted 9800 WLC into Catalyst Center?
Hello Guys, Have anyone done AP grouping in Cisco catalyst 9800 controller. Via using tags and profiles. i have done going through document. but its boarder to understand. Have anyone provide simple understanding it will be helpful. 2 Groups of AP....
Hello and Good Day,I have a question regarding Bonjour mDNS services within a Cisco SDA Fabric.Specifically, I am looking for a guide to set up AirPlay or SONOS services with location awareness so that iPads only see the AppleTV closest to them.Our w...
Below logs found from Wireless controller :*Dot1x_NW_MsgTask_4: Jul 18 02:27:11.714: %LOG-3-Q_IND: 1x_eapkey.c:452 Invalid replay counter from client MAC addres - got 00 00 00 00 00 00 00 00, expected 00 00 00 00 00 00 00 01*Dot1x_NW_MsgTask_3: Jul 1...
C9100のデフォルトのタイムゾーンがGMTなのですがWLCでタグ付けして、NTPに同期させているのにJSTになりません。Syslogの時間などは日本時間になっているのですがshow clockだと「GMT」のままです※時間は日本時間こちらはJSTには変更できないのでしょうか？
Hi!I am running a wifi network for about 1200 users using a splash page with active directory authentication, and I am often experiencing issues with the splash page not automatically showing when an authentication is required. This happens both with...
I have a few questions relating to the new Cisco Custom RF ASIC on the 9K Access Points:1. Is the Cisco Custom RF ASIC also present on the 9176 Access Points2. Can the Cisco Custom RF ASIC be used to contain rogue Access Points and Clients without di...
Whenever we have needed an outdoor bridge, I have always used the 1532 in autonomous mode. They work really well, with few failures. But with the 1532 no longer available, Cisco seems to be forcing everyone to go with a controller based solution - wh...
Hi Team,Can you please assist on this requestcase number: SR 699665269
What is going on:From the U-Boot I am following this recovery method.https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9120axi-access-point/217537-repairing-c9120-c9115-access-points-from.htmlAfter resetting the AP, and logging in, I'm try...
Resolved! C9800 Admin access through GUI with MFA
Hi wireless colleagues, After multiple tries with the configurations I have managed to enable MFA on the C9800 for admin access through CLI by using TACACS+. The integration is done via ISE with NPS as Proxy RADIUS to Entra ID MFA Service in the clou...
Hello all,Does anyone here in the forum have experience with integrating their Ekahau surveys into the Meraki site dashboard? We already own a number of Ekahau Side kick 2 devices and we perform the surveys. What would be involved in pulling those ...
Resolved! MR78 outdoor wireless backhaul
Could I use a two MR78 APs as a wireless outdoor backhaul. I have a light pole with 120V power and It has and Axis camera. I can provide 120V for power injectors for the Axis camera and MR78. Several years ago I used NanoStation M2 for wireless back...
