Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Viewing Wireless Cleints
Hi,Company has issued a return to office policy and lots of our users are using laptops. I want to view the list of clients that my APs are handling. What I'm doing right now is opening my APs on different tabs and let the Carousel addon to flip to t...
Resolved! Chromebooks and 3802 access points
We've just completed some network up grades at four sites. New switches and new access points. The access points are 3802's. The problem is some of our older Chromebooks no longer connect to the 3802's. Swap out a 3802 for a 3702 and the Chromebo...
Hi WLC 8.5.140.0 needs to remove http for security reason. Is it possible to remove it without upgrading ios? thanks
Hello, I noticed on our 5508 WLC that an access point on the roof of one of our buildings is down (roof terrance). On the PoE switch is now shows Ieee PD instead of AIR-CAP1532E-EK9I have done a shut and no shut and I get the same. Nothing shows wit...
Hi, I have a WLC 2504 running ver 8.5.171.0The issue I'm having is with laptop clients connecting to our guest wifi. They do not get the web login page to enter their credentials for guest wifi access. It attempts to redirect to https but gets stuck....
When i configure the ap with Static IP it takes IP and Starts ping in local network but it cant join WLC.
I have recently purchased some MR56 APs and get this message when saving an RF Profile. Why am I now being forced to select a UNII-1 or UNII-2 "5-lo" channel?There were errors in saving this configuration:One or more errors occurred. No changes have ...
Hi guys, Some of users have a issue after AP upgrade from AP1832-I to C9115AXI. Users report their whatsapp web shows disconnect when phone screen turned off. The WLC is using 3504 with firmware 8.10.162.0. I tried debug client and marked the debug d...
Resolved! How do I use the 2.5GB port?
I have MR36 & 46 AP's. We are using Fortinet 426 switches that have the 2.5GB multigig ports. I tried to connect the 2 with a normal cat6 cable but the port speed stays at 1GB. Is there something I need to do on Meraki's side to turn this function on...
Hello Team, i am getting this below error when accessing the network device after creating policy to access network device for internal users. TACACS+ will use the password prompt from global TACACS+ configuration but same device i can access using ...
Hi,As per the data sheet Cisco Catalyst 9115 ap is supported wifi6 . my switch C9300L-48P-4X-E supports only poe+ so what will be the impact Thanks
Resolved! Wireless uptime
Hi,Where i can find wireless uptime menu on meraki dashboard, i already check all menu but can't find that. Appreciate for answer.Thank you
Resolved! Cisco Wireless control system
hey people , as far as we know the Cisco WCS is EOS AND EOL and same goes for adobe flash player which is not supported anymore and WCS requiring Adobe flash player to see data and so on . what is the solution for such case is there any other servi...
Hi All I currently have an Anchor controller (Cisco 5520) with AirOS version 8.5.151.0 and i am going to deploy a Cisco 9804 as a Foreign controller. Can anyone suggest do i need to upgrade the AirOS on my Anchor to the guest EOIP tunnel to be forme...
Hello Team, I have setup EAP-PEAP. 1. created one corp-ssid for all the users. 2. define setting under the gpo policy which is pushing from AD end to all the laptops. 3. i am broadcasting the SSID from my WLC. now my concern here that when user usin...
