A Wireless Bridge Root can be associated to a Access Point No-Root ?
A Wireless Bridge Root can be associated to a Access Point No-Root ?
WIth AP1200 dual radio config 802.11a and 802.11b is it possible to turn one of the radios completely off.Thank you
Bridge can at the same time work like Bridge (Root) and Point Access (Root) ? A Bridge (Root) can be associate to a Point Access (No-Root) ?
In the power setup for the Cisco Aironet Access Points 350, it shows how power is to be supplied to the 350. My question is - why is the ethernet connection from the power injector to the switch (without inline power) needed? I think I understand ...
Hello,I have few pre-Cisco acquisition Aironet (Model #AP4822B) bridges. Are current PC and PCI cards going to function with these access points? If not, where can I get older cards that will function?Thanks,David
Has anybody gotten Apple Airports client using version 2.0 or greater software to work AP 350s configured for LEAP and Dyn WEP as well as a DHCP server.The Mac software I am using is 10.2 or 9.2.2. I can get the client to request a DHCP if I make ec...
Which event must I change in order to get the AP350 to report a configuration change to a remote syslog server? Thanks.
Hi.I'm having problems chanving the configuration of an Cisco 350 Series Access Point running firmware 12.00T.I haven´t got User Manager enabled, so i guess i should be able to change the fields. The problem is that though I'm able to change every fi...
what is the use of a separate strong CHAP/MS-CHAP password in the ACS user setup ? Document said it need to be supported by the AAA client. Do I need to configure anything in the AP ( AAA client ) to match this password?
I have configured LEAP+MAC authentication through an ACS. The first time a user tries to connect there is a MAC authentication and a LEAP authentication. But every 10 minutes there is a LEAP re-authentication of the user.Is that normal? are these 10 ...
Please any one can advise me why the bridge said that it works at 11Mbps but when we do a testing with 2 Aironet bridge AIR-BR350-E-K9 the maximum throughput I can get in the idea situation is 6.6 Mbps only. So what is the real throughput of Aironet ...
Ok, I'll be the first to confess I'm an idiot......I have to install a shot tomorrow, and left all the hardware at work. Today, I'm supposed to be going out and getting the masts. Without the "U" bolts on hand, what diameter mast should I be buying...
Whenever I removed an allowed MAC address from the filter when the MAC address is still associating to the AP, I have an intermitently timeout access to the AP from wired LAN. If the MAC address is not being used at that time and I remove it from the...
In passing this Access Point from One Engineer to another someone has misplaced the power supply for this access point. Can anyone tell me what pin-out and mW is for this 5VDC input is? Looking into the connection, which is arch shaped, there are thr...
I am using MAC and Leap authentication thru ACS. The default unicast filter is disallowed. However, when I tested the MAC auth out, some MAC address in the allowed list can pass but some are failed. even the MAC is allowed. Any idea where I have miss...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-27-2025 06:05 AM | ||
02-18-2025 11:22 AM | ||
02-13-2025 10:43 PM | ||
02-13-2025 08:57 PM | ||
02-04-2025 03:06 AM |
User | Count |
---|---|
10 | |
7 | |
2 | |
1 | |
1 |