i have setup a lab, trying to do N+1 with 9800 L-F & virtual(8.10.113), i have followed the Documents.in Configuration > Wireless > Mobility, status and PMTU value is NA.
Forum Posts
Hi,I am having a bit of a curious problem with a Chromecast where the device shows up on the WLAN (VLAN 3) to the mobile device, but not to browsers in the LAN (VLAN 30). I am following the setup for the "scenario 2" where the SSID multicast interfac...
Hi, We have cisco iw 3702 wgb acting as a client in metro (max speed 80km/h). Trackside ap:s {cisco 1532). 2.4ghz freq. Now I need some advice. Associations are working great and data rate is m15-s2 when high speed roaming. Problem is poor wireless p...
Hello, I have an AP Aironet 1832i with Mobility Express 8.8 installed, and I can't seem to find the following:- Session Timeout (https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-8/config-guide/b_cg88/wlan_timeouts.html). It mentions I nee...
Hello guys, Would like to know if the AP can be installed outdoor, knowing that we have a bad weather. So i checked the datasheet but still no information "ipx". Thank you.
Which channels should I have listed in my DCA 5Ghz channel list? Should I be using or when should I use the Extended UNII-2 Channels Thanks
Resolved! mobility express cisco 1562
i have a cisco 1562 with mobility express, then my app 1562 is a converter in a wlc. can i connect a ap 1532 with this wlc (1562)ap ?
Hello, everyone. Now I'm building WLC and AP by building a new site.The configuration is 1 WLC, 14 APs, and I would like to have the AP manage traffic if the WLC fails later.So I'm trying to do AP mode with Flexconnect, but the clients say they can't...
Hello all,I am trying to configure AP 3800 support 5GHz with below commands but not succeed(please see attached file also). Please help (Cisco Controller) >config 802.11-abgn band ap VNSGNB09AP 5GHzRadio [Slot 0] does not have external antenna plugge...
I have a new C9800-L-F-K9 configured for Webauth via ISE 2.4. I can authenticate as the ISE login page is displayed and I input my creds. ISE shows client authenticated, but on 9800 client still shown in Web Auth Pending state and post login page fai...
Hello experts, We have two APs, A in main conference room and B in small conference room and there is drywall between two rooms, but the both APs are very close in distance, maybe 20feet. From last week, we have employees work in both room due to co...
My predecessor configured the guess SSID with a customized web auth page. I found the document about how to download it to the controller but is there a way to upload it from the controller to my PC, so I can review it and edit it? Thanks,Difan
Resolved! Cisco 3850 wirelsss - Can't configure wpa akm psk set-key ascii 8 <word>. Prompt decryption failed.
Hi, anyone manage to configure on Cisco 3850 wireless wpa key using the ascii 8 encryption ? I'm able to configure using the >> security wpa akm psk set-key ascii 0 <pre-sharedkey>. But since it is not encrypted, i'm able to see the PSK string in pla...
Dear All, Need your feedback regarding cisco wireless lan controller 5520 Do we need to upload cisco boot image for cisco wlc 5520 controller in UCS Server..I am able to login to Cisco Intergrated Management controller but after that server goes to...
Resolved! Cisco Catalyst 9000 Series models
Greetings;I am planning to purchase Cisco Catalyst 9000 series switch (to replace Cisco 3850 with wireless features), but I am a bit confused about the models of 9000 series. I saw Catalyst 9200, 9300, 9400 Series switches, etc... The switch I want i...
