Hi, I'm deploying the Catalyst 9800-CL Cloud Wireless Controller in AWS using the CloudFormation template. After deployment I'm unable to login into the GUI interface using the username/password I specified in the template screens or SSH using the ke...
Forum Posts
I have a WAP121 Access Point that continues to work perfectly since installation in early 2014. I am unable to access the setup/configuration. I have the correct IP address for the AP as shown on the router's IP list but when trying to access the AP ...
Hi, I need guide convert from CAPWAP 8.151.0 to LWAPP or Mobility Express to LWAPP on Cisco Aironet 1832i?Anyone have guide ? Thanks.
Hello,We have Cisco 2800 Mobility Express. version 8.10.151.0. Cisco support 2700 series AP on mobility express.(https://www.cisco.com/c/en/us/td/docs/wireless/access_point/mob_exp/810/release_notes/b_ME_RN_810.html) How to add Cisco AP 2700 with -UX...
Hello, I have been ordered to troubleshoot an inability of a Cisco 9500-- IOS XE Version 17.03.01 to communicate with monitored devices, yet the log seems edited... Device ‘a’, Authentication failed for request from 192.168.197.639.Device ‘b’, Authen...
Hi,we are using single AP1560 as standalone controller for 100 APs (it support only 100 APs). now we are adding 40 more APs in network. my question is can we add another AP 1562 in Network and configure as second Active controller for new APs ?is it ...
Resolved! MR AP compatibility with MR42
I have MR42 APs which are EOL and their replacement is the MR44. We cannot get the MR44 for at least a year, so I am looking at the MR36 which is in stock. Can the MR36 and MR42 work together? This is for a small ~20 users office space. APs will be s...
First off, forgive me if this is a simple matter. I have searched all over and have not found a valid answer. I have a 5506w-x that I got for a lab setup as I am a first-year student in a cybersecurity college course. It was still configured from the...
Hi All, Please help with below Access points if they support SNMPv3 and if not, do they at least they support snmpv2 or v1.Cisco AIR-CAP3502E-E-K9AIR-LAP1262N-A-K9 Thanks in advance.
we have a pair of 9800-80 HA (RMI+RP) running on Version 17.03.04prd5, few days ago the primary unit (chassis number 1, priority2) crashed due to a hardware issue and we have been shipped a new Box.Right now the secondary unit (chassis number 2, prio...
I purchased this to help with poor WiFiconnection in the bedroom upstairs I’ve since realised there designed for use with a wireless LAN controller (?)They were priced with in my limited budget and yes I now know there old stock and no longer support...
Resolved! 无线控制器查看流量
请教怎么在无线控制器2504/5520上查看AC和AP的流量
Resolved! Channel Utilization Discrepancy
Our MR56 AP's are reporting acceptable channel utilization (usually ~2%, up to 10%). However, devices on the ground show much higher utilization with 3-5 SSID's per channel. The AP's are mounted to the ceiling 20 feet high. Should we manually assign ...
Team today I saw one setup which I want to ask why it was. At the site there is one Local WLC and 2 AP these are locally only. I saw that both AP was in flex mode even WLC is local. Then I checked Corporate SSID there I found that under the Advance t...
HelloI am looking for some information on why I do don't see a selection for "n" Wifi in the WLAN section of the controller?I wanted to do G/N but no choice for this. Thank YouJoseph
