Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
My friends - Is there likely to be any difference in terms of range or signal penetration through walls? I have a number of spaces where it would be handy to only use one access point and so if it means using a slightly bigger one I’m fine with it. R...
Hi everyone!I have a MPLS network with about 50 WAP's (AIR-AP1852I-Z-K9) and WLC that connected to DHCP server and everything was working fine. we recently added a new site and for new site we couldn't use fiber link so we decided to use Cradle point...
Does anyone know if the Cisco RF Planner is capable of creating a heat-map of actual utilization (i.e., when there are 20 active users and what the wireless coverage is like)? Another question is can it be created plugging 20 users and 60 devices an...
Resolved! CAWAP AP CLI registration check
I was trying to figure out if there is a way from the CLI on an AP (a 3702i in this case) if I could tell which controller the AP was actually associated to. I can run a "show capwap client config" to show what the config is, but I have found some c...
Cisco AIR-CAP3502I-A-K9, and 8540 Wireless ControllerLast week I got a call that there was no Wireless in one of our Buildings (Performing Arts Center aka PAC). After checking it, all 6 3502 APs were not providing wireless.The APs have a solid green ...
Hello Experts,I have a problem on the Cisco Catalyst 9130AXI, which is running as a EWC.For some time, can not say exactly since when, I can no longer display in the GUI under Administration -> Software Management to perform an update. The page is th...
Hi all,assuming my wireless client IP subnets are created on a non-VSS, stack, or SVL device.FHRP is realized using HSRP.So in my wireless VLAN, there are link-local Multicast messages for the group address 224.0.0.102 (HSRPv2).If I have Multicast su...
Weird issue.AP 1832i----switch(no trunk)-----DMVPN--WAN--DMVPN--WLC5520 8.5.151.0Sometimes PSK Auth process fails with message "wrong PSK" on Device. Sometimes it works. Seems like there are "timeslots", when it works - and when it does not work.Seem...
Hello I have had a number of issue trying to view my account on my mob phone. I keep getting a password message - which I cannot access due to the email it is sending it is not something I can access. I have been told to delete the free version acco...
Greetings! Thank you for the overwhelming response to the First and Second EFT refresh of 8.10MR6! We are excited to announce the third refresh of 8.10 MR6 EFT Program for PRODUCTION deployments. While the CCO release of 8.10MR6 is just a few weeks a...
Please see the diagram.WLC ---------- Switch --------- PC | AP WLC C9800, PC and AP are connected to the Switch via vlan10(10.0.10.10/24). Dhcp pool is configured at the Switch with two scop...
Hi, does anyone know which regulatory domain to use for Honduras?
Hello Meraki Community.Please, I need some help to understand the "RF Performance Table" inside Meraki MR Datasheets.Here is an example:MR36 Datasheet - Cisco MerakiIf I understand correctly the "RF Performance Table" is indicating the conditions whe...
i have two controlers in HA N+1 i want to failover all the access points from primry to secondy what is the best method to avoid downtime (i am havinj around 400 access points and arounfd 100 ap gorups) secondly if i want to change the ap group W...
I have installed 2 AP directly to MX with Injector in placed same model and same configs on both, bounded to Template.One of them showing 1000mb speed on Ethernet 1 of MR and another one showing only 100mb instead if 1000mb.
