Hi All, I've recently added TACACS to web UI authentication but it seems I can only have two privledge levels: Level 1 - Can only view monitoring tab, no config settings or troubleshooting. Level 15 - can view all and make changes. Is there a way I ...
Forum Posts
Platform: 9800-L-FSoftware: 17.3.2a SSID:WPA(AES/TKIP)+WPA2(AESCCMP128) running simple PSK authentication. No L3 Auth involved. The DHCP forwarding is orchestrated by the 9800 via the SVI. After scouring the configuration and comparing 9800 & 5508 th...
Hello Experts, I am facing an issue with Mobility express AP/WLC.1st WLAN: 802.1x with ISE as Radius2nd WLAN: 802.1x with Cloud RADIUS SERVER Switch Port config where AP/WLC is connected: interface GigabitEthernet3/0/43switchport trunk native vlan 80...
Hi After setting up initial configuration for C9800 wlc, i try to access the wlc. but I got the below message. Anyone has this kind of experience? Thank you
I Have an AP U-boot and I change the boot partition then, it run well but not joined the controller .. what is the reason?
Hello AllPlease could you confirm that the reason for restarting of the access point is related with Poe issue?Last reset from power-onI didn't find logs for Poe issue...Logs from the switch:016229: Jun 17 10:32:42: %LINEPROTO-5-UPDOWN: Line protocol...
Hello team, Im new in the wireless world and I'm reading docs about the controller Catalyst 9800-CL and I'm facing some doubts, we can see 3 interfaces in the manual, they are:1- Device Management interface;2- Wireless Management interface;3- High Av...
Resolved! MacBooks slow wireless
Having a weird issue with some MacBooks we are using on wireless. When we leave the MAC address on standard setting we get speed throttling on download (2 mbps down and 100 up) but if we change the MAC address, we get full download speeds (100 down a...
Hi board,If I disable and enable an AP using:ap name myAP shutdown ap name myAP no shutdownIt takes ages until the 5 GHz radio is ready (example 2802)What I see in the 5 GHz radio summary is after the AP is enabled, that there is a small "#" sign aft...
Resolved! "show traplog" for Cisco 9800 / IOS XE
Hi,with AireOS we had both "show logging" and "show traplog" and they were both useful but for different purposes. "show traplog" was really helpful to troubleshoot something "client or AP related" in cases where there was no SNMP trap receiver. I wa...
Hello Everyone! I have two types of RF cables AIR-CAB005LL-N and CAB-L400-5-N-N According to specs AIR-CAB005LL-NN(m)-STR to N(m)-RALMR-400, 5 foot RF cableType: outdoor DB (direct burial) CAB-L400-5-N-NN(m)-STR to N(m)-RALMR-400, 5 foot RF cableTyp...
Unable to configure more than one snmp trap receiver with same snmp community string in AireOS WLC. AireOS WLC(Cisco Controller) >config snmp trapreceiver create ABCDEFGH 10.10.10.11SNMP Trap Receiver added!(Cisco Controller) >config snmp trapreceive...
Hello experts, @balaji.bandi @Scott Fella @Sandeep Choudhary @Rob Ingram I have two 1704 APs connected with 2504 Controller. Both APs look fine within Controller login but Physically, One AP having green blinking light whereas other AP is having...
Dear All,could you tell us which CPU and Memory ranges (values in %) are fine for the 8540 and C9800 WLCs and from what percentage we need to trigger warning and alerts / take actions.Thanks very much
Hello Geniuses, I have WLC 2504 and running with 1700 and 2700 series APs at the moment. Couple of AP 1130 also were working fine till few days ago. After a reboot of WLC due to the power failure, all of a sudden, all 1130 APs are not joining to the ...
