Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
WLC#chassis redundancy ha-interface local-ip 192.168.0.2 255.255.255.0 rWLC#$-interface local-ip 192.168.0.2 255.255.255.0 remote-ip 192.168.0.1WARNING: Changing the chassis HA interface IP address may result in a configuration change for th...
What is the reason for the client delete in the debug below on a WLC 9800? Deleting the client, reason: 135, CO_CLIENT_DELETE_REASON_MN_AP_AUTH_STOP, Client state S_CO_L2_AUTH_IN_PROGRESS Thanks
We have cisco 5520 wireless controller connect to 88 Aps, Suddenly in the morning some of the clients got connected and some of them get connected but says no internet.connected clients are both 2.4 and 5GHZ clients. Please advice
I am upgrading 2 5520 controllers HA, and 2 Guest Anchors to 2 9800L's in HA and 2 9800 Guest Anchors. We have a 3502's and 3800's in environment now. Upgrading to 9130's I am looking for the best way to upgrade and have them possibly run in parall...
Hi everyone, I have couple of Wireless Access point:model: AIR-AP1852I-I-K9boot image: 8.10.142.0 and also tried 8.5.140.0I made a factory reset to the access point, and reconfigured it, then created an SSID but it never broadcast it. the AP was joi...
Hi!I can see channel and signal level and the capabilities of a client.In addition I would like to check the live bitrate, spatial streams and channel width for a client? Where can I see these?My idea would be to see if the client is actually using i...
Hi Wireless folks,I'm playing around with a C9800 and I'm wondering where the CoPP configuration and documentation is. I bet the box does some CoPP out-of-the box and I want to understand how it works and whether it can be tuned.For example, I'm wond...
Hi everyone, I've got a simple question. Existing wireless infrastructure (AirOS or IOS-XE) and I need to lifecycle my APs. Is it possible, to use DNAC PnP, to assign hostname, primary and secondary controller, AP-Group/Tags to an AP without the need...
Resolved! Mapping Specific SSID to multiple Vlans
Hello Dears,If we have a core switch with multiple subnets for the same SSID , on local mode this would be fixed via interface group , however i faced a situation in a Flexconnect environment where for SSID X is multiple small subnets configured on t...
Hi Anyone can explain the DHCP override in the below picture. Thank you
I am using my AP in EWC mode. I am using Windows 2019 NPS as the AAA authority. I have set up admin (web & ssh) access and have set up 802.1x for one of my WLANs and it is working as expected. I would like to have a few WLANs that are restricted b...
Hi AP(3600) joined to WLC and WLAN are configured, but I cannot see its ssid. Did I miss some steps? Anyone can help to give some suggestions? Thank you
Hi WLC management interface ip address is 10.0.10.12/24 and dhcp server ip is 10.0.10.10/24 located at vlan10 in a switch. The dhcp scope is 10.0.10.0/24. The user can get ip address 10.0.10.21/24. but if the dhcp scape is changed to 10.0.10.128/25, ...
Hi All, I have made this video for Cisco Pitch the Future Contest in Malaysia which talks about Wi-Fi 6 and EWC Demo. Please feel free to view the video below and please support me for this contest by giving the video a like as the Contest will end o...
If I configure the 3602 with an AIR-RM3000AC-E-K9 module in local mode the Admin Status of the Module (Slot 2) is Enabled and the Operational Stauts is UP. If I then change the mode of the AP to bridge the Admin Status gets disabled and the Operatio...
