Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi All, I would like to integrate Active Directory with Wireless controller. Can any one help me on this how can I do this? what will be the settings for users laptop? peap or LEAP
AP: 2800, 3800 WLC: 5520OS: 8.5 or later Feature: FlexDFS Could you tell me if the wireless clients connected to AP 2800/3800 can avoid being disconnected from AP even when the radar is detected in primary channel when enabling FlexDFS in AP?For in...
Hi,What are the rules for external MIMO antennas?Accesspoint such as AIR-AP1852E, C9115AXE have multiple RP-TNC connectors for external antennas.1. Do i have to put antennas on all 4 connectors? Or is it o.k. to just use one or two? What to do with t...
Resolved! Wifi 3G/4G/5G and b/a/ac/ax
Hi Wifi 3G/4G/5G are 3/4/5 generation. while a/b/ac/ax are different band respectively. My question is what is relation between 3G/4G/5G and a/b/ac/ax? Thank you
Hi all, I am currently able to manage my WLC AIR-CT3504 using wireless connection but no able to do so using wired connection even though i have ensured that i am using the same ip. Please advise. TIA!
I am just wondering if it is possible to use Dual band antennas with a cisco 1572 in single band mode? In my mind if the antenna can function with either frequency if the 1572 is set to dual band mode it should be able to work fine with the unit se...
Dear all,Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https. Does any one know why?Thanks
Hi, Upload speed is low in guest SSID, download is good. the upload and download speed in company ssid is good. Anchor controller is behind Palo Alto firewall. TCP MSS value is 1200.
When I start my router it's giving me an error message and was wondering if someone could help me out.error reads as:"Configuration of vLAN subinterfaces and maininterface within the same bridge group is not permittedPlease configure the bridge group...
I am trying to get 25 3700 ap's to join an existing 5760 wireless controller. There are already 150+ ap's joined and have been for 2+yrs. I have licenses and the country code is correct. An ap will appear to join the controller and then disappear ...
Hi all, I have around 50 2702 APs joined to a WLC5508, however, some of the APs are occasionally reset by controller. One of the APs reboots more frequently than other APs for around 3-4 times a week. The controller software version is 8.3.133.0 and ...
Currently running new WLC 5520 on above code.Channel Width is set to 40MHz and DCA using 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140But for some reason APs are broadcasting on 80MHz and 160MHzCan't see any th...
In Linux what is the command to generate an MD5 on a backup in the CISCO Prime to verify Backup Gary
Fellow Colleagues, Is anyone familiar with what the "Default" setting for Rx Sop Threshold represents? This configuration can be found under Wireless > Advanced > Rx Sop Threshold. The other setting options are defined in the help file, but I'm not q...
Hi folks, I have an issue with CPI v3.3.0 at the moment where although it is performing a sync with my WLCs the total AP counts are a few hundred off and so I have a bunch of APs which are displayed as being 'Not Associated' with any WLC. This in tur...
