Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Currently running new WLC 5520 on above code.Channel Width is set to 40MHz and DCA using 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140But for some reason APs are broadcasting on 80MHz and 160MHzCan't see any th...
In Linux what is the command to generate an MD5 on a backup in the CISCO Prime to verify Backup Gary
Fellow Colleagues, Is anyone familiar with what the "Default" setting for Rx Sop Threshold represents? This configuration can be found under Wireless > Advanced > Rx Sop Threshold. The other setting options are defined in the help file, but I'm not q...
Hi folks, I have an issue with CPI v3.3.0 at the moment where although it is performing a sync with my WLCs the total AP counts are a few hundred off and so I have a bunch of APs which are displayed as being 'Not Associated' with any WLC. This in tur...
Resolved! Map Foreign Controller interface to Anchor Controller vs use interfaces defined on Anchor Controller
In Cisco guest WLAN architecture, regardless LWA & CWA variations, have Foreign Controller and Anchor Controller to configure. I'm confused with some configuration variations in terms of guest interfaces used on the Anchor Controller:Scenario 1:Forei...
If an AP is setup as an OEAP, and the ssid in use is set to local switching, will the client still be dropped off at the same physical interface the AP is on? Or... will clients on an OEAP automatically be centrally switched regardless of how the ssi...
Does the 8540 Wireless Controller support any network programmability abilities for configuration and to pull operational state info (ex: Netconf, Restconf, XML, JSON, YANG data models)?
Just replaced 13 1602i's with 1852i-b-k9's. Previous devices were pulling proper 172.22.160.0/22 ip's.only 3 of the 13 acquired proper ip's. of the rest, 3 reported 192.168.0.101 (1 each switch) the rest nothing.Switch's report proper CDP signatur...
Hello, We are running a WLC 5508 and we seem to be having a hard time casting to Apple Devices. Android Devices - no problem. Running Firmware / Software Version 8.3.143.0 Our issue is that Apple products (iPhone) can go through the set-up process ...
Hi, I have a wireless network with 802.1x authentication, contain Cisco Aironet CAP-2702i connected to a controller. Today, i want to configure an autonomous access point for make a bridge between my network 802.1x and my AP. Thank you for your help.
Hello, We have a remote WLC 5520 (fw 8.2.130.0), some 3802E and I APs in flexconnect mode, local switching.On our WS-C3650-48PD switches, we have this configuration for APs ports:interface GigabitEthernet1/0/48description AP PORTswitchport trunk nati...
Fellow colleagues,Where can I find guidance on how to properly configure a single, dual-radio, AP so that the 5GHz is serving clients full time while the XOR radio acts as a full-time sensor? We are using a 3504 WLC and our APs are 2802i. If there is...
Problem: In our end client's environment there is an android TV, which faces intermittent disconnection. This is particular to this device only. When ran debug I am seeing orphan packet being sent by the client. We tried configuring static IP for t...
Hii am looking for some help, i am currently have a situation where my client whats to report and view the mac address for all mobile device with in the company's wireless bubble, connected to an SSID or not (probe request) Does anyone know of a sol...
i have my cisco access point 1130AG ip address assigned by my DHCP but i cannot access the page setting when i enter it on the browser url address. It says page cannot display
