Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello, I added a Lightweight AIR-CAP3702l-E-K9 in my test network and succesfully linked it to my WLC2504. However, after a power restart of the whole thing infrastructure, it lost the config and the linkage to my controller. I read on a discussion t...
how to update firmware cisco air 1815cisco AIR-AP1815I-E-K9 ARMv7 Processor rev 5 (v7l) with 1016204/557336K bytes of memory.Processor board ID FCZ2443R36UAP Running Image : 8.5.140.0Primary Boot Image : 8.5.140.0Backup Boot Image : 0.0.0.0AP Image t...
Has anyone found a way to make auto-LAG work on Cisco AP's? I have 9136 AP's on a Cat 9300 switch stack and it would be great for this feature to work.
how to upload .tar SW file to Air AP1142N-A-K9 using tftp or using CLI after login to it.
Hello, I must design a solution with several IW9165D for a customer with existing mutiple sites en subnets. All the IW9165D are intented to see each others. Question : Is the IW9165D capable of routing operations between differents private subnets su...
User can't connect ssid with eap-tls authentication method but not prompting username and passwor. If there is no certificate in client machine did username and password will prompt ? Note - user is able to connect other ssid where we are using eap-m...
Hi,I'm interested in buying a used 3504 to replace my current aging 2504 - and I was wondering if the 3504 comes with the same base ap license scheme as a 2504.For clarification, my current 2504 - which I previously bought used - came with just the p...
Hi,Is there some way easy to view how many GB a client have used?On my old setup (AP2802 mobility express) I had on the frontpage dashboard a view saying how many GB each client have used.On my 9120 setup (embedded wireless controller) I have to go t...
Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00163S - IMAGE_VARIANT_STRING=HAACANAZAS - OEM_IMAGE_VERSION_STRING=CRMS - Boot Con...
Hello All,We have been thinking about improving our guest and byod wifi access to accommodate multiple use cases.One of the main goal for the new solution is to cater all connections using single SSID.We are using Cisco 9800 wireless controllers. In ...
I have a WLC 2504, but I don't have the credentials to access it and I'm looking to reset it to factory settings. However, I don't have access to the console because the BAUD rate and console port parameters were changed, so I only see strange charac...
Hi,I am confused with Cisco explanation about how TPC works, especially TPC hysteresis. Cisco says that:If Tx_Ideal is higher than Tx_current, then a power increase is recommended. If Tx_Ideal is lower than Tx_current, then a power decrease is recomm...
I have 50 WAP connected to a WLC 5508. When I backup the config I don't see the custom settings I put in some WAP. Where are the WAP settings saved at ?
We have a guest network setup on WLC 9800-40 version 17.12.2 with ISE (3.1)as radius server. Central web auth is configured with self registered user. Captive portal loads fine and registration of new user is fine.However after login with credentials...
Hello,Is there an easier way to view how many GB a client has used on a 9120 setup (embedded wireless controller)? On my old AP2802 (Mobility Express), the dashboard showed usage data for each client directly on the front page.With the 9120 setup, I ...
