Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Which channels should I have listed in my DCA 5Ghz channel list? Should I be using or when should I use the Extended UNII-2 Channels Thanks
Resolved! mobility express cisco 1562
i have a cisco 1562 with mobility express, then my app 1562 is a converter in a wlc. can i connect a ap 1532 with this wlc (1562)ap ?
Hi,I am in charge of IT at a small K-12 school. Recently, some laptops on campus have begun to experience a perplexing issue ONLY when they are in one particular building. These laptops will automatically connect to an SSID broadcast by the MR42 unit...
Resolved! Will MR42E work without external antenna
Hi all,Can someone please give me some advice whether MR42E will work without external antenna?The reason I asking is I not sure if the MR42 will have good coverage for my office so looking into option of buy MR42E instead.If coverage is not good eno...
Hello, everyone. Now I'm building WLC and AP by building a new site.The configuration is 1 WLC, 14 APs, and I would like to have the AP manage traffic if the WLC fails later.So I'm trying to do AP mode with Flexconnect, but the clients say they can't...
Hello all,I am trying to configure AP 3800 support 5GHz with below commands but not succeed(please see attached file also). Please help (Cisco Controller) >config 802.11-abgn band ap VNSGNB09AP 5GHzRadio [Slot 0] does not have external antenna plugge...
I have a new C9800-L-F-K9 configured for Webauth via ISE 2.4. I can authenticate as the ISE login page is displayed and I input my creds. ISE shows client authenticated, but on 9800 client still shown in Web Auth Pending state and post login page fai...
Hello experts, We have two APs, A in main conference room and B in small conference room and there is drywall between two rooms, but the both APs are very close in distance, maybe 20feet. From last week, we have employees work in both room due to co...
My predecessor configured the guess SSID with a customized web auth page. I found the document about how to download it to the controller but is there a way to upload it from the controller to my PC, so I can review it and edit it? Thanks,Difan
Resolved! Cisco 3850 wirelsss - Can't configure wpa akm psk set-key ascii 8 <word>. Prompt decryption failed.
Hi, anyone manage to configure on Cisco 3850 wireless wpa key using the ascii 8 encryption ? I'm able to configure using the >> security wpa akm psk set-key ascii 0 <pre-sharedkey>. But since it is not encrypted, i'm able to see the PSK string in pla...
Dear All, Need your feedback regarding cisco wireless lan controller 5520 Do we need to upload cisco boot image for cisco wlc 5520 controller in UCS Server..I am able to login to Cisco Intergrated Management controller but after that server goes to...
Resolved! Cisco Catalyst 9000 Series models
Greetings;I am planning to purchase Cisco Catalyst 9000 series switch (to replace Cisco 3850 with wireless features), but I am a bit confused about the models of 9000 series. I saw Catalyst 9200, 9300, 9400 Series switches, etc... The switch I want i...
Hello all,I have a four AP MR42 conected fine , but today i had a cut on SSID , when i researched after on event log for access point i detected this :Single device packet floodradio: 2, state: end, alarm_id: 20 « hide reasonreceived_packetand Auto R...
Hi Guys, I need your help.I have a Controller AIR-CT5520-K9 Does not work with module GLC-LH-SMD=. Two side with same GLC-LH-SMD=.Only one port SFP used.Please troubleshoot this problem
I need The default administrative username and password for AP521.I try admin:admin cisco:cisco
