Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello,Would you guys know how I could get/enable a controller to generate a log when the buffer is full and overwrites older logs?
Hi guys, I have 2xWLCs 3504 on HA-SSO configuration. WLC1 is the primary WLC2 is the standby-hot For some reason I CANNOT ping WLC1 management and redundancy-management interfaces, but I CAN access WLC1 management interface via HTTPS/SSH. On the ...
Hi All,We have installed 60 cisco access points in a site. all are working fine, except 10 access points. all the user are connecting to 2.4 Ghz radio and no users are connecting with 5.0 Ghz in those 10 access points only. Same users are able to co...
Hi, I have a controller with 20 APs. But I just need CPI to manage 8 access points. Can it be done if I have 8 Prime licenses? Thanks!, orm
Morning, We're trying to monitor several behavior in our wireless environment for a further project related to AI Regarding documentation from 8.2.X release (we're on 8.2.170), there are a lot syslog message that we don't see in our log. We set the...
The AP that’s designated as the controller keeps going offline in our monitoring system because the IP address of the AP keeps reverting to 0.0.0.0 in the Nomadix (Nomadix is our Gateway/Firewall onsite). The AP has 2 interfaces, the mobility express...
Hi fellow community members, Yesterday I did an upgrade of a 5508 WLC HA pair with only Flexconnext AP's (mix of 3702 and 1602 AP's) distributed all over Europe. We went from version 8.2.151 to 8.5.135. After the upgrade and before the reboot of WL...
Hello, randomly i can't access my vWLC by WebUI and also all clients on Dot.1x losing connection and can't re-authenticate. Non dot1x clients staying with network. This problem appears with low and high utilization in network at any time. I can acces...
Hello Community! I have a Spark Kit Plus system and and i am trying to setup Proximity on it. What ive done so far is below: Enabled Proximity on the camera system is connected to the local network and registered with CUCM Installed Proximity on...
Resolved! Unable to remotely access 5508
This is terrible. I had a 5508 WLC that I couldn't access remotely but Prime reported that it was still serving APs. TAC RMA'ed it. Got the replacement, upgraded the code and I could access the GUI. I restored the config from a backup and guess wh...
Resolved! 9800 embedded experiences?
Hello, The last generation of WLAN controllers integrated in switches had some problems and limitations.Does anyone know whether the 9800 embedded also requires access points to be connected directly to the switch that houses the controller? So far...
Hi Guys, Can anyone help on the Prime infrastructure disk utilisation /var. it prevents NCS application to start. To get NCS application to start manually deleted some small log files, ncs cleanup also done but same 100% in /var.. ade # df -h...
Dear Cisco community,I am a newbbie on Wireless controller implementations and I require to implement a WLC 5508 in a HSRP core switch configuration. I want to implement certain level of redundancy by connecting the WLC 5508 to both core switches.Giv...
Hi I have a WAP321 which has the wireless disables and I have no idea how to enable it, and with my limited tech knowledge am struggling. I cannot see it when attached to my Sky Q router, or when attached to laptop. Any guidance welcome please. T...
Hi I have some troubles with one of my clients on my wireless networks. The session timeout on my WLC is 30min. per default and the clients gets disconnected every 30 min as expected. But this one client takes about 1-2 minutes before i reconnects....
