Hi, I have installed a Virtual Wireless Controller (version 8.3) on ESXi and I am working with the setup. I have a question abount ports and VLANS. Now the controller has only one port, the management-interface is connected to this port. But now I ...
Forum Posts
Resolved! DHCP mandatory vs static IPs
On a 5508 running the latest code, If I select DHCP mandatory on the Advanced page for a given WLAN, does that stop a client from using a static IP address, or are those two compatible such that they can coexist? I mean, if a client is set up with a ...
Resolved! Airport Runway Wireless Solution
I have a situation where we are looking to implement Cisco Wireless Solution for the Airport. When I say Airport, I am referring to runways rather than the other part of the Airport. This is more about the running vehicles on the runways to be able...
Hello, I have 2 WLC with 2 SSID and I have seen the IPAD have problems to connect to wifi. They try to connect but sometimes do and sometimes do not. Then they say: "impossible to connect to wifi X". This only happens with IPAD or iphones, not with o...
Resolved! wlc2504 Dynamic VLAN Assignment
I installed DHCP, Radius in Ubuntu to configure Dynamic VLAN Assignment.I can get DHCP and log in as Radius. I want to use several VLANs for one SSID.But I can't.https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/71683-dynamic...
Dear Sir,How can i transfer license my smart domain to client domain?
I have a 9840 that I setup from defaults on the CLI. How do I get the GUI out of express setup?I cannot find this anywhere in the configuration guise. Also, what do the different "install modes" such as "install" or "bundle" modes.How do I change the...
Hello all. I am facing a strange issue on a deployment of 34 Meraki APs, Users on site are not roaming to the nearest AP.The site is mostly made of mac book pro and Apple and android devices.There are 5 SSID’s each on there own subnet. Capacity d...
Just started to investigate a medium/large network setup where it seems all of the LWAPs are connected to switchports configured as trunks and all of the LWAPs are in local mode. Each switchport is configured like this... interface GigabitEthernet2/0...
Dear Experts, I have two questions about Cat9800 WLCs TACACS+ admin access configuration. 1. Once 9800 is configured to do TACACS+ for its webUI admin access, no matter if logging with WLC local admin accounts or AD accounts, there are always two use...
Resolved! AIR-AP1815I-E-K9 from CAPWAP to ME ?
Hello community,Is it possible to convert an AIR-AP1815I-E-K9 access point to ME (Mobility Express) version ? Already have some K9-C version working, but ME portal is unable to upgrade those K9 by itself. Thanks for your advises. Anthony
Hi Team, I have configured TWO VLANS for LAN and WIFI... Wifi is configured and connected on ASA MaManagement port and wifi is working finewe are not able to access from Wifi vlan to lan VLAN Can any one help me to resolve the issue thankssuresh
Hello Meraki Community,I have been told that the Meraki Layer 7 Firewall solution available in Meraki MR AP dashboard is based on best effort, as it is not able to block certain traffics even if they have been defined within the Layer 7 firewall rule...
Hello, I have just setup a test vWLC in a lab and connected a AIR-CAP2702I-E-K, the controller can see the AP, I have configured a few SSIDs but I cannot see them being broadcasted?Any suggestions? Wireless
Hello together, i am currently struggling really hard to get a AP2802i to run as a Bridge / WGB Mode. I have the CAPWAP Version and the Bridge-mode should be available, but its NOT. When i try to change to mode from "local" to "bridge" i get this Mes...
