The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi, I have configured two ISPs (WAN1, WAN2). VPN with anyconnect was already working for both ISPs. Today when doing final tests, VPN for ISP1 on WAN1 is not working anymore. ISP2 on WAN2 still works. ASA log shows: 1 Starting SSL handshake with clie...
I am able to ssh to the 8851 just find and do a 'test key soft1' command just find.But not able to the the advanced commands like 'test key set' or serv.Is there something I am missing?Is there something in CUCM that I need to enable to do these comm...
Hi, I'm having problems to redirect incoming call from sip trunk to CUE AA,- I have a Cisco 3945 and a NME-CUE , VID: V04- the sip trunk provider only gives the last four digits.- sip trunk number 8800 redirects to extension 100. Works fine.- sip t...
Hello everyone,While learning EIGRP, I encountered a challenge regarding metric calculation. I understand that each router calculates the Feasible Distance (FD) to reach a destination. As part of this process, each router first calculates the cost to...
Hi all;Recently, I encountered a failed AnyConnect installation on a client and the normal uninstallation procedures did not answer. Are there any official Cisco's documentation regarding on how to force uninstall operation and then clean up a failed...
Hi everyone... I'm new to the bot world so my apologies if this question is silly. I am looking to create/use a bot to send notifications from Github whenever any Pull request is created, approved, rejected, actioned. Is there already a bot available...
Hi Have upgraded Cisco Catalyst 9800-40 Wireless Controller from 17.6.6 to 17.09.05 and it was working fine for few hours. I notice it went back to its previous version when I login next time. Any reason why? please help
Hi community,I need to replace intake for port side exhaust on a pair of switches. I can powered off them. We are receiving PSU's port side exhaust and FAN's port side exhaust.Is there any procedure for doing this?Regards,
Hi Expert,Recently, one port on our 9200 switch went to err-disable state and the status LEDs are all off. The port configuration is as below: it is connected to a desktop PCThe logs is as below, it looks before it goes to err-disable state, the port...
greetings all,I am trying to configure the guest wifi access on ISE (version 3.2.0.401).I don't want the password to be displayed on the self-registration success page, we really need the guest to sign in to their email to get the password. So I conf...
Please help. I have an ASA 5506-x connected to a 3750 swich. I cant ping 8.8.8.8 or anything external from the switch. I cant ping the other vlan subnets either ( the ASA has the route back to these). However, I can ping 8.8.8.8 and tracert successfu...
Hello everyone.I am currently using WLC5520-8.10.196 and AP9115AXI in the office. I have noticed that some clients occasionally roam to farther APs. These clients are all Intel's WIFI6 network cards. The frequency band of AP is 80MHz.The AP3800 serie...
Has anyone found a simple way to automate the deletion of old DNAC Backups?Our DNAC is set to backup to a Linux server each night, however, unless we remember to regularly go to the DNAC backup page and delete old backups the Linux server eventually ...
Hi All, I'm new here. I would like to set up spam quarantine notification on my ESA C395; refer to https://www.cisco.com/c/en/us/support/docs/security/email-security-appliance/118692-configure-esa-00.html.my question, I only have two options: send no...